Question

Name: Problem 2 (30 points) (a) Based on the lecture notes of Week 5, obtain the state transition matrix 0(t) = At for A= 1;

0 0
Add a comment Improve this question Transcribed image text
Answer #1


Problem 2 I- A The state transition matrix &(t)= eat for a State matrix A is given by, eAt = [((SI-A)-) where I is the identNeu, ($1-A) - - *(க-2)-3 UN Aleu 8( -2 -3 = 29-3 =(8-3) (3+1) Thus, (SI-A) = 8-2 Tearow (S-3)(s+I) (S-3)(s+1) மேs-> -1 S-2 = A + B & By Partial fraction ? (8-3)(8+1) (6-3) (8+1) A= Lt (6-3) x(4-2) = { By residue ? 3 (4-3) (6+1) 4 methodهه ر (9) (9) A = It (4-3) x 3 (1+) (3-و 3% A - 3 A 4 3- - - x3 (ا+ه) ا -3 4 (الا) (3-و) ا-دلا + B A - (2 + 1) (3) (او) (دو) AB= It (4+1) X & dal (8-3) (3+1) B = - - - 1 14.) = 1 / 2 Therepote (ST-A)Acest ten thoa tron) 2 4 19 3 – 3 4(9-3) 4(+1) 3 +which is the required state transition materise $(t). Note; L (e-at) = 1 I leat) - I . S-a b) We have the zero-input state re: 2(t) = (1 4 Bet) - letet) 7.7 ( # (etet) #fortet) - = 1 + 6 - ) - * (* -t) (este-t)- (se#get) 1li ent -e-t 0.135 ! -0.135 Y(t)= cz(t) = [O] [ Y(t)= e-t Y(6) 9 = 0.135 Thankyou.. ..

Add a comment
Know the answer?
Add Answer to:
Name: Problem 2 (30 points) (a) Based on the lecture notes of Week 5, obtain the...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • STATE SPACE SYSTEMS USING MATLAB Problem 2: Obtain the unit-ramp response of the system defined as...

    STATE SPACE SYSTEMS USING MATLAB Problem 2: Obtain the unit-ramp response of the system defined as follows lu. y=[1 0] |xi Show both the input ramp, and the system output response curve on a single graph.

  • Problem 5 (20 Points): For the circuit shown below, the input is the current source, I(t) and the...

    Problem 5 (20 Points): For the circuit shown below, the input is the current source, I(t) and the output is eo. 1). Find the state variable model. Take ec and IL as state variables (refer notes from Chapter-6). 2). Apply Laplace Transform on the state variable model (from part-1) and show that the transform of the output (eo) is given by the expression: 사스 ; if the initial conditions, L(0) and ec(0) are known. Note: ec(0)-eo(0) R L R L...

  • PARTS: a-c Problem 1 (40 points) The rotational system shown in this diagram has a single...

    PARTS: a-c Problem 1 (40 points) The rotational system shown in this diagram has a single torque input, T(t), and a single angular displacement output, (t). Also shown are the shaft polar moment of inertia, J, torsional spring constant, k, and rotational viscous damping coefficient, c. From the law of rotation (sum of the moments equal to polar moment of inertia times angular acceleration), we obtain: jä(t) + c)(t) + ko(t) = T(t). This ordinary differential equation is second-order, linear...

  • Tutorial 2. Incompressible Navier-Stokes equations 18 September, 4-5 pm in FN2 In Lecture Notes 1 the Navier-Stokes equ...

    Tutorial 2. Incompressible Navier-Stokes equations 18 September, 4-5 pm in FN2 In Lecture Notes 1 the Navier-Stokes equations (momentum balance) for incompressible flow were derived. They were eventually written in the following form dr In this equation, the viscosity μ and the density ρ are constants. We now consider two simple flow configurations. Config. 1. The steady state flow of a liquid in the space between two very large static parallel plates at distance H of each other in the...

  • please write code in MATLAB as well 5. (12 points) Create the following signal in Matlab:...

    please write code in MATLAB as well 5. (12 points) Create the following signal in Matlab: x[n] = u(n) - u[n-6] a. Mathematically compute yi[n] = x[n] * x[n] where * means convolution. Now use the conv command to perform the convolution. Graph x[n) and the resulting y(n), both over the interval Osns 20. How many non-zero terms does y(n) have? Does your computational result agree with the Matlab result? b. Repeat a. but this time with yz[n] = x[n]*h[n)...

  • CSCI 112 C Programming Database Lab This lab will focus on the use and manipulation of...

    CSCI 112 C Programming Database Lab This lab will focus on the use and manipulation of structures. Each section of the lab should be designed within its own function, passing parameters as necessary. You are to construct a C program, database.c, that will retrieve and manipulate a company's payroll database, payfile.txt. The data for each employee should be read into a structure containing the following field identifiers: first : 7 characters maximum, initial : 1 character maximum, last : 9...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT