Part 1) calculate the quantity of concrete required to place a 40 by 40 ft 6...
Question 2 How much concrete (CY) is required for an 7 inch thick slab for a building with an 54 foot by 123 foot footprint? Question 3 If 14.25 ft of cement are used in making a batch of concrete and using the 1:2:3 ratio of cement to sand to aggregate, how many cubic yards of concrete can be made? Question 4 How much concrete (CY) is required for a foundation wall with the following dimensions: - Thickness = 8...
Design a concrete mix in accordance with the B.R.E. method and
calculate the quantity of each constituent material for trial mix.
The specification of the concrete mix is:
1. Design a concrete mix in accordance with the B.R.E. method and calculate the quantity of each constituent material for trial mix. The specification of the concrete mix is: • Characteristic strength at 28 days: 40 N/mm² • Standard deviation : 8 N/mm • Proportion defective : 5% • Cement type :...
Johnson & Johnson has been awarded a contract to build a 4-seat outhouse for a rich man. The exterior dimensions will be 10 ft by 40 ft. The pit must be 10-ft deep so as not to fill up too quickly. The excavation has a bottom dimension of 20 ft by 50 ft and a top dimension of 60 ft by 90 ft with the cast-in-place concrete pit walls also being 10 ft by 40 ft. The borrow material has...
1 Review The channel is made of unfinished concrete. (Figure 1) Part A Determine the required slope if the flow is to be 380 ft/s when the depth is y = 6 ft. Take n = 0.014. Express your answer using three significant figures. Figure < 1 of 1 > EVO ALQ IT vec a 0 2 ? So = 7.97 • 10-4 Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining 8ft Provide Feedback Next >
Q4. An industrial building is to be supported on a series of 14 -in square prestressed concrete piles which will be driven 45 ft into the following soil profiles:Depth (ft)Soil classificationFriction angle phi^(') (deg)Relative density D_(r)N_(60)Unit weight gamma (lb//ft^(3))0-10.0Silty sand (SM)3340%1210010.0-16.5Sandy silt (ML)3150%1611016.5-35.0Fine to medium sand (SW)3562%3012535.0-65.0Well-graded sand (SW)3768%35126The groundwater table is at a depth of 15 ft and all of the strata may be assumed to be normally consolidated. These piles have been designed without the benefit of any...
Reinforced Concrete
Exam 1 CiEn 470, Reinforced Concrete Last Name, First Name Problemt3[40% esign a 24-foot long reinforced concrete beam to support a dead load of 500 lb/ft (including the beam self weight) and a live load of 1,500 lb/ft The architect has requested a beam width of 9 inches. Use 60 ksi steel and S ks concrete. (Assume #3 stirrups) a) D b) Sketch the detailed cross-section of your design c) Analyze your design for safety.
A 5 in thick simply supported
reinforced concrete one-way slab is part of a roof system. It is
supported by two masonry block walls, as shown below. Assume a
superimposed dead load (roofing, insulation, ceiling, etc.) of 15
psf and a roof live load of 30 psf. Check the adequacy of the slab,
including the required shrinkage and temperature reinforcement. Use
= 4,000 psi and = 60,000 psi.
1. A5 in thick simply supported reinforced concrete one-way slab is part...
9. a. A spring has constant k-5lb./in. Its natural length is 12 inches. What is the work required to compress it to 9 inches? b. A 100 ft. cable weighs 40 lbs. Find the work done in winding the cable onto a winch, if the cable is hanging vertically c. An unknown positive charge q is placed at the origin. The force F (in Newtons) with which this charge repels a unit positive charge is given by F-kq/r, where k...
Part A The channel is made of finished concrete and has the cross section shown in (Figure 1). The downward slope is o.0006. Determine the fow of water through the channel when y- 5 ft. Take n 0.012 288.3 ft3 /s X Incorrect; Try Again; 2 attempts remaining Figure 1 of 1 Provide Feedback 2 ft s ft 6 ft
Part A- Answer all questions (Total Marks for Part A: 120) Part A- Question 1 (Total Marks for Part A - Question 1: 24) A 140mm thick concrete slab is supported by a series of parallel 460UB82.1 steel beams at 2400mm centres. Assume there is sufficient bond between the steel beam and the concrete slab to enable the materials to act together as a composite unit Assume for steel E 200 GPa ? 280 MPa for concrete E-25 GPa ?...