Problem 2: +3 V VB ?? Figure 2 Consider the circuit shown in Figure 2, with...
*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...
*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...
IX With reference to the transistor amplifier shown in Figure QB4 below d For the bipolar transistor circuit of Figure QB4 the following DC bias conditions were measured: VB made. 1.6 V and VBE =0.6 V. Detemine the value for RA, stating any assumptions e) Using these same conditions, calculate the current in Re and deduce the current in Rc, stating any assumptions made. Hence find the voltage across Rc and explain whether this voltage is suitable for this amplifier...
D. For the transistor circuit shown in Figure 7, assuming that the transistor is in the forward active mode, and B = 100 and VBE = 0.7V, calculate Base current 1B Collector current Ic (iii) Emitter current le (iv) Collector to emitter voltage Vce and (v) Voltage across the 2009 resistor v 3 80022 10 kV W VCE VBE مت + + 1 2001} 1 1
Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteristics of a transistor circuit. 2. To study the bias circuit of a transistor circuit. B. Apparatus: 1. DC Power supply 2. Experimental boards and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Digital multi-meter....
draw a base biased circuit and refered to question 5 and
complete table.
please draw the fixed bias diagram circuit and follow throught step
on the next question.
Figure 1. Bipolar junction transistor under base bias/fixed bias 5. In the circuit drawn in Figure 1, label the components with the following values: Base voltage, Collector voltage10V Base resistance Collector resistance Base - emitter voltage 2.7 k2 0.7 V 160 6. Connect the circuit drawn in Figure 1 on the breadboard....
Question 3. Unregulated supply Rz IL Vin IR Ib (a) The circuit on the right shows a series regulator connected to the output of an unregulated power supply. The transistor has B =50, and a 6 volt Zener diode is used. When the load current, Il, is 1 amp the de input voltage from the unregulated supply, Vin, is 11 volt, VBE = 1 volt and the Zener diode current, Iz, is 20 mA. For these conditions, calculate Iz (i)...
(iii Assuming that the transistor in the circuit in Figure 2 is in forward active mode and VBE 0.7V and B = 200, calculate the DC bias values of the base current, the collector current and the voltage VCE 20 knS 12 kS 4.7 pF 47uF 3.3 knS 200S Figure 2
Problem #4 In the voltage-divider circuit shown in Figure, the no-load value of y, is 4 V. When the load resistance R, is attached across the terminals a and b, v, drops to 3V. Find R 40.2 w 20 V 20v & R2 vo {RL
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...