Q.11. Calculate the base, collector and emitter currents for the circuit given in Fig. 01. Also,...
Problem 5 Given the following circuit, assume the following parameters VBB IV, RB 220 k, RC = 2 k, VCC= 10 V, VBE(on)-0.7 V, and B 200 a) Calculate the base, collector, and emitter currents and the C-E voltage, also, calculate the transistor power dissipation b) What transistor configuration does the circuit resemble? Vcc=10V RC=2k Rg=220 kQ VCE VBB= 1V o + VRE IB
Consider the npn BJT with a turn-on voltage V1 = 0.70 V, and a saturation emitter-collector voltage V CE/SAT) = 0.20 V. (a) [20 points) Consider this transistor in a common- emitter circuit (Re = 0). Design this common- emitter circuit to produce the IV (Ic vs. VCE) characteristic and load line (LL) as shown in the graph. Your answers are the following: a drawing of the circuit; the values of Vcc, Rc, VBB, and Ra; and the value for...
1) Calculate the value of the base current IB. (in μA) 2) Calculate the value of the base collector current IC. (In mA) 3) Calculate the value of the collector-emitter voltage VCE. (In V) Required information In the circuit below: RB = 820 kN, Vcc = 12 V, RC = 3 kN2, and Bdc = 100. Note: The transistor is silicon. Vcc w Rc Re Bdc
In solving the problems, assume constant-voltage model for transistors. In case that base-emitter voltage is not specified, use 0.75V for VBEoN of NPN transistors and VEB. oN of PNP transistors. Using the constant voltage model, you will not need to use the given values for L.. Compute the bias point of the circuits depicted in Fig. 5.109. Assume β-100. s 6 x 10-16 A, and VA Hint: you are supposed to find the collector current and to check if the...
2. In the following current mirror circuit, Vcc -10V, and the three transistors, Q1, Q2, Q3, have the same saturation current (i.e.,IssIs), and with V for active mode is 0.7V. Then, the three beta values are given by: β91-100, ßQ2-50, and ßQ3-200. The thermal voltage is ντ-25mV. Assuming that you need an output current of i1mA: ref db (a) Find the collector, base, and emitter current for all three Q1 O2 transistors when ia 1mA. (b) Find the refern ie....
In the circuit of given below, Vsig is a small sine wave signal with zero average. The transistor B is 100. a) Find the value of RE to establish a dc emitter current of about 0.5 mA. b) Find Rc to establish a dc collector voltage of about +5 V c) For RL10 kS2 and the transistor ro 200 k2, draw the small-signal equivalent circuit 5. of the amplifier and determine its overall voltage gain +15 V Re O Vo...
Can I get help with part g through part r, please? Given the following Common-Emitter Amplifier with Voltage-Divider Bias: The transistor is a Silicon device with B160 (Beta 160) and transistor r.= 30 kn: 20 V 34.7k LAL = Vou 35.10 31.1k LRE $3900 03 - Find the following quantities in parts a through where means Quiescent DC): a) Thevenin Voltage and Thevenin Resistance Re b) Base Current la Collector Current le d) Emitter Current le e) Transistor Collector-Emitter Quiescent...
1. Two directly coupled common emitter amplifiers are shown below in Fig. 1. Since base current IBase2 of the transistor Qp is much smaller than the collector current of QN, simply ignore I Base 2 current while solving the problem. Vsig is a purely AC signal. Find DC operating points (Ic, VCE) of the transistors. ON I Qp VA= OV B = 150 VE(ON) = 0.7 V VESAT) = 0.2 V VA= OV B = 70 V(ON) = 0.7 V...
(2+5 pts) Consider the bias circuit below for a transistor amplifier designed for active region operation. The desired bias point parameters are lg = 3 mA and Ic = 2.97 mA. Assume VBE- 0.7 V and VT=25 mV. Determine the emitter voltage VE . Choose the best answer. VCC +15 V Vc RBB VB LVE V BB RE 500 S2 1.49 V O2v 01.5V O 0.7V
draw a base biased circuit and refered to question 5 and complete table. please draw the fixed bias diagram circuit and follow throught step on the next question. Figure 1. Bipolar junction transistor under base bias/fixed bias 5. In the circuit drawn in Figure 1, label the components with the following values: Base voltage, Collector voltage10V Base resistance Collector resistance Base - emitter voltage 2.7 k2 0.7 V 160 6. Connect the circuit drawn in Figure 1 on the breadboard....