Problem 2: A pressure-fed bearing has a journal diameter of 50.00 mm. The length of the...
i need an ansower to every part of this quastion
(a) Design a central annular-groove pressure-fed bearing with an l/d ratio of 0.5, using SAE grade 20 oil, the lubricant supplied at 30 psig. The exterior oil cooler can maintain the sump temperature at 120°F for heat dissipation rates up to 1500 Btu/h. The load to be carried is 900 Ibf at 3000 rev/min. The groove width is 14 in. Use nominal journal diameter d as one design variable and...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 78.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 10 and SAE 30 lubricants operating at...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance of - 0.075 mm. The bushing bore has a diameter of 75.15 mm and a unilateral tolerance of 0.1 mm. The busing is 75 mm long and supports a 2585 N load. The journal speed is 750 rev/min. Find the minimum oil film thickness and the maximum film pressure for SAE 20W lubricant at an operating temperature of 65 °C for the minimum clearance...
A 50 mm diameter pressure fed journal bearing is operating at 50 rev/s under a load of 5 kN giving a projected unit load of 2 MPa. Half journal length is l' = 25 mm, and radial clearance is c = 25 microns. Oil inlet temperature is maintained at 30 °C and average temperature is to be kept at 70°C. Viscosity of the oil used is then 12 mPa.s. What is the minimum required supply pressure [kPa] that maintains this...
Assume Kr 1 and Ka In a journal bearing assembly, the shaft has a diameter of 88.900 mm and a bilateral tolerance of + 0.076 mm. The bushing bore diameter is 89.027 mm with a unilateral tolerance of +0:0.119 mm. The bushing length is 50 mm. The SAE 30 oil has an average operating temperature 60°C. For a minimum radial clearance, a speed of 1000 rev/min, and a radial load of 20 kN, find the maximum bearing pressure and its...
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rpm. For the minimum clearance assembly find the minimum film thickness and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of...
3. A 100 mm diameter shaft is supported by a bearing 50 mm long with a minimum oil-film thickness of 0.02 mm and radial clearance of 0.06 mm. It is lubricated by SAE 30 oil. The bearing carries a load of 4 kN of at 900 rpm. Employing the design charts, determine The temperature of the oil film • • The coefficient of friction • The friction power
2. A shaft carrying a 10KN load is supported by two identical plain journal bearings. The shaft, which normally rotates at 3000 rev/min has, at the bearing region, a nominal diameter of 50 mm and a length of 16 mm. Starting with a radial clearance ratio of 0.0015 and neglecting thermal effects a) Calculate the temperature of the lubricant which will produce an eccentricity ratio of 0.7 if the oil used is SAE10 b) Comment of the necessity to supply...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film thickness, the heat loss rate is SAE 20 oil and the operating temperature is 60 C.
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is...
D Question 6 2 pts Estimate the minimum oil film thickness (m) in a sleeve bearing (B- 360°) carrying a design load of 3 kN at a rotational speed of 600 rev/min. The bearing diameter is d 44 mm, the bearing length is I 0.6d and the diametral clearance is 1 um per mm of the bearing diameter d. The bearing operates at a Sommerfeld number of S-0.2
D Question 6 2 pts Estimate the minimum oil film thickness (m)...