We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
rer ab sa power originale! 2.59 An op-amp voltage follower is powered by £10-V power supplies....
RI Power supply to op amp +12 V mind Vout = + 10 V sinewave Vin = + 200 mv sinewave -12 V The non-inverting amplifier is powered + 12 V and -12 V. What would happen to some outputs if the power supplies were +5 V and -5 V? How would these supplies restrict the input voltage range?
Capacitor is connected to secondary (1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transformer is connected to a 50Hz, 230Vus power supply. A 2700μF filter capacitor is used. A current of 1.5 Amp is drawn from the supply (i) Sketch a schematic diagram of the setup (ii) Calculate the mean dc output voltage (ii) Assume that each diode conducts for one-twelfth...
Q2: An amplifier operating from t 15-V power supplies is fed with a sinusoidal voltage having 1 V peak and delivers a sinusoidal voltage output of 12 V peak to a 1-kΩ load. The amplifier draws a current of 6.5 mA from each of its two power supplies. The input current of the amplifier is found to be sinusoidal with 0.1 mA peak. Find (a) the voltage gain, (b) the current gain, (c) the power gain, (d) the power drawn...
1. A 480 V (rms) source supplies power to two loads connected in parallel. The first load draws 80 kW and 30 kVAR. The second load draws 100 kVA at a power factor of 0.6 lagging. a) Draw the power triangle for the first load and determine its power factor; b) Determine the current (both magnitude and phase, using the source voltage as the phase reference) drawn by the first load; c) Draw the power triangle for the second load...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
11) 20pts. The zener limiter circuit s V R often used as a low power voltage regulator for a DC power supply. This circuit is an example in load A) Find R so that the maximum power dissipated in the zener diode is Po for any possible value of Road given P, Vin and B) What is the maximum current that the load can draw before the zener stops regulating the voltage? C) When the circuit is regulating the voltage...
Q1. You are given a 12 V DC power supply. You are expected to develop a voltage divider to achieve a voltage of nominal 5V value using a pair of resistors from the E 12 range, with the restrition that you are not expected to draw a current of more than 1 mA from the 12 V DC supply i. Develop a simple circuit showing the possible values for each resistor pair, and the range of the DC output possible...
10. Draw below a schematic of an inverting op amp circuit operating from a single +voltage DC supply, that has a gain from input to output Av = 5 WITHOUT DISTORTION, with a 1kΩ load resistor. The input will be a 500mVRMS sinewave. BE SURE TO SHOW ALL POWER AND GROUND connections and POWER VOLTAGE LEVELS. Use Esupply = +20V, and assume 1 V headrooms.
Q4/// What is the current of the 40 v ?voltage source of the circuit below SA 202 w 802 w 103 40 20 V 40 V Current source Voltage source leave question o 13 A 0.5 A O 12A O 10 A 1A O أخرى: Q5/// The maximum power dissipated in a 4 load is 100 w when connected to a d.c. voltage V and internal resistance R. Calculate: the current in the load, internal *.resistance R, and voltage V...
Please solve the Worksheet +V Figure 5. Op amp negative feedback circuit. Node Signal Figure 6. Current Relationships R, Node n (0 Vw 3.3.Discovery Exercise: In your worksheet, use the information above to develop a formula for the gain, which you will use in the exereises below. Pre-Work: Prior to lab, review exercise and complete Worksheet #7. Experimental Procedure: 5.1.Negative Feedback Amplifier: In t 4. 5. he exercises be low, record the measured value of the selected resistors and enter...