Homework Answers
Q= UA
T
U:OVER ALL HEAT TRANSFERE COEFFI IENT =1W/m2K
A; SURFACE AEA =325m2
T=
temperature difference=33-0=33k
Q=1*325*33=10.725KW
Add Answer to:
.0 W/m2-K, including the effec An anaerobic digester cover has an overall heat transfer coefficient U...
A counter-flow heat exchanger is stated to have an overall heat transfer coefficient of 284 W/m2.K...
A counter-flow heat exchanger is stated to have an overall heat transfer coefficient of 284 W/m2.K when operating at design and clean conditions. Hot fluid enters the tube side at 101°C and exits at 71°C, while cold fluid enters the shell side at 27°C and exits at 42°C. After a period of use, built-up scale in the heat exchanger gives a fouling factor of 0.0004 m2 K/W. The surface area is 93 m². Assume both hot and cold fluids have...
The solar radiation incident on the outside surface of an aluminum shading device is 1300 W/m2...
The solar radiation incident on the outside surface of an aluminum shading device is 1300 W/m2 . Aluminum absorbs 10% of the incident solar energy, and dissipates it by convection from the back surface and by combined convection and radiation from the outside surface. The convection heat transfer coefficient is 10 W/m2 ·K for both surfaces, and the ambient/surrounding temperature can be taken 20 °C for both convection and radiation. Assuming that the aluminum shade has a uniform temperature, determine...
Cold conditioned air at 10°C is flowing inside a 1.5 cm thick square aluminum (k = 240 w/mK) duct...
Cold conditioned air at 10°C is flowing inside a 1.5 cm thick square aluminum (k = 240 w/mK) duct of inner cross section of 25x25cm at a mass flow rate of 1.0 kg/s. The duct is exposed to air at 35°C with a combined convection-radiation heat transfer coefficient of 15 W/m2K. The convection heat transfer coefficient at the inner surface is 75 W/.m2.K. If the air temperature in the duct should not increase by more than 1°C determine the maximum...
Calculate the overall heat transfer coefficient for the following: 4. hi 1 100 W/(m2-K) 11/4-standard type...
Calculate the overall heat transfer coefficient for the following: 4. hi 1 100 W/(m2-K) 11/4-standard type M copper tube ho 200 W/(m2.K) Make the calculations assuming that the wall resistance is negligible and again assuming that it is not. Compare the results.
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation,...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V< 0.33 m/s is determined experimentally and is expressed as h = 5.05 KairRe131D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m°C. The thermal conductivity and the kinematic...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation,...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V 0.33 m/s is determined experimentally and is expressed as h=5.05 kairRe13/D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m-°C. The thermal conductivity and the kinematic viscosity of...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation,...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V< 0.33 m/s is determined experimentally and is expressed as h=5.05 kairRe13/D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m-°C. The thermal conductivity and the kinematic viscosity of...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
Heat transfer 5 نقاط A plane wall (k = 45 W/m.K). 10 cm thick, has heat...
Heat transfer
5 نقاط A plane wall (k = 45 W/m.K). 10 cm thick, has heat generation at a uniform (2 rate of 8000 KW/m3.The two sides of the wall are maintained at 180°C and120°C. Neglect end effects; calculate the magnitude and position of * .maximum temperature
A house has a composite wall of wood (exterior) (k = 0.12 W m-1 K -1...
A house has a composite wall of wood (exterior) (k = 0.12 W m-1 K -1 , 20 mm thick), fibreglass insulation (k = 0.045 W m-1 K -1 , 70 mm thick) and plasterboard (interior) (k = 0.25 W m-1 K -1 , 10 mm thick). Determine the total heat loss through the wall when the inside temperature is 20 °C, the outside temperature is -10 °C, the inside heat transfer coefficient is 15 W m-2 K -1, and...
A counter-flow heat exchanger is stated to have an overall heat transfer coefficient of 284 W/m2.K when operating at design and clean conditions. Hot fluid enters the tube side at 101°C and exits at 71°C, while cold fluid enters the shell side at 27°C and exits at 42°C. After a period of use, built-up scale in the heat exchanger gives a fouling factor of 0.0004 m2 K/W. The surface area is 93 m². Assume both hot and cold fluids have...
Cold conditioned air at 10°C is flowing inside a 1.5 cm thick square aluminum (k = 240 w/mK) duct of inner cross section of 25x25cm at a mass flow rate of 1.0 kg/s. The duct is exposed to air at 35°C with a combined convection-radiation heat transfer coefficient of 15 W/m2K. The convection heat transfer coefficient at the inner surface is 75 W/.m2.K. If the air temperature in the duct should not increase by more than 1°C determine the maximum...
Calculate the overall heat transfer coefficient for the following: 4. hi 1 100 W/(m2-K) 11/4-standard type M copper tube ho 200 W/(m2.K) Make the calculations assuming that the wall resistance is negligible and again assuming that it is not. Compare the results.
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V< 0.33 m/s is determined experimentally and is expressed as h = 5.05 KairRe131D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m°C. The thermal conductivity and the kinematic...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V 0.33 m/s is determined experimentally and is expressed as h=5.05 kairRe13/D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m-°C. The thermal conductivity and the kinematic viscosity of...
During air cooling of oranges, grapefruit, and tangelos, the heat transfer coefficient for combined convection, radiation, and evaporation for air velocities of 0.11<V< 0.33 m/s is determined experimentally and is expressed as h=5.05 kairRe13/D, where the diameter Dis 0.1 m. Oranges are cooled by refrigerated air at 5°C and 1 atm at a velocity of 0.3 m/s. Given: The thermal conductivity of the orange is given to be k = 0.50 W/m-°C. The thermal conductivity and the kinematic viscosity of...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
Heat transfer
5 نقاط A plane wall (k = 45 W/m.K). 10 cm thick, has heat generation at a uniform (2 rate of 8000 KW/m3.The two sides of the wall are maintained at 180°C and120°C. Neglect end effects; calculate the magnitude and position of * .maximum temperature
Most questions answered within 3 hours.
-
4) A firm is hit by increases in its wage rate, w.
a) How does this...
asked 38 minutes ago -
You have just been hired by the EPA to help with the new gas
mileage standards...
asked 23 minutes ago -
A square current loop 5.4 cm on each side carries a 510 mA
current. The loop...
asked 2 hours ago -
What are five tips in conducting knowledge assessment/literature
review research? Each of these tips needs to...
asked 3 hours ago -
Antigen presenting cells link innate and adaptive immune
responses. In the theoretical scenario where phagosomes cannot...
asked 3 hours ago -
Dealing with conflict, in my opinion, is a skill and an art. I
believe that those...
asked 4 hours ago -
6. A long straight wire with circular cross section and radius
1.5 cm carries a 1.2...
asked 4 hours ago -
Deacon Corporation has provided the following financial data
from its balance sheet and income statement:
Year...
asked 5 hours ago -
List and discuss at least three variables from everyday life for
which you expect the variable ...
asked 5 hours ago -
A high-pass filter consists of a 1.60 μF capacitor in series
with a 125 Ω resistor....
asked 5 hours ago -
A newly developed artificial intelligence has trouble
distinguishing hand-written numbers from hand-written alphabets.
There are pictures...
asked 5 hours ago -
The carbonate ion CO3 2- has multiple resonance structures.
a. Draw them and assign the hybridization...
asked 5 hours ago