A concentric tube, parallel heat exchanger is used to warm cold well water running on the...
A concentric tube, parallel heat exchanger is used to warm cold well water running on the inside pipe from 10°C to 25°C overa meter of pipe using steam running through the outside pipe that enters the system at 140°C and leaves at 100°C. The inside pipe is made of copper and has an inner diameter of 4 cm, with a wall thickness of 0.25 cm. The outside pipe is made of a very-well insulating material, has a diameter of 7 cm, a mass flow rate of 0.05 kg/s, and a specific heat of 2,017 J/kg*K. If the average convective coefficient of the steam side has been calculated to be ho= 500W/m2*K, what is the convective coefficient of the water side used to maintain the desired temperature change? Assume properties of water at 300K.
Homework Answers
Add Answer to:
A concentric tube, parallel heat exchanger is used to warm cold
well water running on the...
A concentric-pipe parallel-flow heat exchanger is to heat water (cp = 4.18 kJ/kg.K) from 20°C to...
A concentric-pipe parallel-flow heat exchanger is to heat water (cp = 4.18 kJ/kg.K) from 20°C to 80°C at a rate of 1.2 kg/s. The heating is to be accomplished by geothermal water (Cp =4.31 kJ/kg.K) available at 160°C at a mass flow rate of 2.0 kg/s. The inner pipe is thin-walled and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640 W/m2.K, determine the length of the pipe required to achieve...
Two-pipe concentric concentric) for cooling the engine oil with the help of a water stream in...
Two-pipe concentric concentric) for cooling the engine oil with the help of a water stream in a large diesel engine a reverse (opposite) flow heat exchanger is used. Water at a flow rate of 0.3 kg/h from inside pipe with an inside diameter of 56 mm It flows. The inner pipe is made of stainless steel with a heat transmission coefficient of 16 W/mc and is meat (wall its thickness is 3 mm. Apart from this there is another pipe...
QUESTION 1: Heat Exchanges A concentric tube parallel floween s hot water saturated liquid from 30...
QUESTION 1: Heat Exchanges A concentric tube parallel floween s hot water saturated liquid from 30 to 90%Catate of St. The exh , having thermopla properties similar to air, enter and exit the exchange 254 and 100 p ectively. The heat force 1000 W/mK The water pipe has a diameter of 50 cm a) Determine the required length for the exchanger. b) Assuming water flow inside the tube to be fully developed, estimate the convection heat transfer coefficient c) If...
A shell and tube heat exchanger with one shell pass and two tube passes is used...
A shell and tube heat exchanger with one shell pass and two tube passes is used to heat 8.82 kg/s of fluid from 15.6 °C to 60 °C by using saturated steam at 150 kPa. The steam is condensing on the outside of the tubes with h= 15 kW/m2.K. There are 50 tubes with an outside diameter of 1.91 cm and a wall thickness of 0.211 cm. If the fouling coefficient on the inside of the tubes is 5678 W/m2.K,...
Twenty [kw] of heat is to be removed from 375 [k] water flowing at 0.15 [kg/s] into the inner pipe of concentric tube heat exchanger. Cooling water enters the annulus at 290 [k] and leaves at 320...
Twenty [kw] of heat is to be removed from 375 [k] water flowing at 0.15 [kg/s] into the inner pipe of concentric tube heat exchanger. Cooling water enters the annulus at 290 [k] and leaves at 320 [k] with a flow in the opposite direction of the inner flow. The diameter of the thin- walled inner pipe is 2.5 [cm] a) b) c) Calculate the exit temperature of the hot fluid and the mass flow rate of the cold fluid...
A concentric tube heat exchanger for cooling lubricating oil consists of a thin-walled inner tube of...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
4. The heat exchanger, shown below, is being used to generate vapor from saturated water at 385-K. The other side of the exchanger is condensing saturated steam at 400-K、The heat exchanger has 1...
4. The heat exchanger, shown below, is being used to generate vapor from saturated water at 385-K. The other side of the exchanger is condensing saturated steam at 400-K、The heat exchanger has 15, S-cm ID thin-wall copper tubes, each 10-em long between the tube sheets. Calculate the steam condensation heat transfer coefficient for the tubes of this exchanger Calculate the rate of exchanger (10) a. vapor generation (kg/sec), m, in the tubes of this (10) a. 400 k 帛? 40...
A concentric tube heat exchanger of length L = 2 m is used to thermally process...
A concentric tube heat exchanger of length L = 2 m is used to thermally process a pharmaceutical product flowing at a mean velocity of u_m,c = 0.1 m/s with an inlet temperature of T_c,i = 20 degree C. The inner tube of diameter D_i = 10 mm is thin walled, and the exterior of the outer tube (D_0 = 20 mm) is well insulated. Water flows in the annular region between the tubes at a mean velocity of u_m,h...
6 Water is heated in a pipe by exchanging heat with a warmer fluid that flows outside the pipe. Inside diameter of the pipe is dn 0.045 m and outside diameter dour0.05 m. Mean velocity of the water i...
6 Water is heated in a pipe by exchanging heat with a warmer fluid that flows outside the pipe. Inside diameter of the pipe is dn 0.045 m and outside diameter dour0.05 m. Mean velocity of the water in the pipe is um-0.31 m/s and the bulk temperature is 323 K (density 988 kg m-3; viscosity 0.00055 kg m' sı. Pr 3.56, thermal conductivity k 0.64 W m1 Kt). The material of the pipe has thermal conductivity k 0.61 W...
Required information A shell-and-tube heat exchanger is used for cooling 47 kg/s of a process stream...
Required information A shell-and-tube heat exchanger is used for cooling 47 kg/s of a process stream flowing through the tubes from 160°C to 136°C. This heat exchanger has a total of 100 identical tubes. each with an inside diameter of 2.5 cm and negligible wall thickness. The average properties of the process stream are: p = 950 kg/m”, k = 0.50 W/mK, Cp=3.5 kJ/kg.K, and -20 mPas The coolant stream is water (cp=4.18 kJ/kg K) at a flow rate of...
A concentric-pipe parallel-flow heat exchanger is to heat water (cp = 4.18 kJ/kg.K) from 20°C to 80°C at a rate of 1.2 kg/s. The heating is to be accomplished by geothermal water (Cp =4.31 kJ/kg.K) available at 160°C at a mass flow rate of 2.0 kg/s. The inner pipe is thin-walled and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640 W/m2.K, determine the length of the pipe required to achieve...
Two-pipe concentric concentric) for cooling the engine oil with the help of a water stream in a large diesel engine a reverse (opposite) flow heat exchanger is used. Water at a flow rate of 0.3 kg/h from inside pipe with an inside diameter of 56 mm It flows. The inner pipe is made of stainless steel with a heat transmission coefficient of 16 W/mc and is meat (wall its thickness is 3 mm. Apart from this there is another pipe...
QUESTION 1: Heat Exchanges A concentric tube parallel floween s hot water saturated liquid from 30 to 90%Catate of St. The exh , having thermopla properties similar to air, enter and exit the exchange 254 and 100 p ectively. The heat force 1000 W/mK The water pipe has a diameter of 50 cm a) Determine the required length for the exchanger. b) Assuming water flow inside the tube to be fully developed, estimate the convection heat transfer coefficient c) If...
A shell and tube heat exchanger with one shell pass and two tube passes is used to heat 8.82 kg/s of fluid from 15.6 °C to 60 °C by using saturated steam at 150 kPa. The steam is condensing on the outside of the tubes with h= 15 kW/m2.K. There are 50 tubes with an outside diameter of 1.91 cm and a wall thickness of 0.211 cm. If the fouling coefficient on the inside of the tubes is 5678 W/m2.K,...
Twenty [kw] of heat is to be removed from 375 [k] water flowing at 0.15 [kg/s] into the inner pipe of concentric tube heat exchanger. Cooling water enters the annulus at 290 [k] and leaves at 320 [k] with a flow in the opposite direction of the inner flow. The diameter of the thin- walled inner pipe is 2.5 [cm] a) b) c) Calculate the exit temperature of the hot fluid and the mass flow rate of the cold fluid...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
4. The heat exchanger, shown below, is being used to generate vapor from saturated water at 385-K. The other side of the exchanger is condensing saturated steam at 400-K、The heat exchanger has 15, S-cm ID thin-wall copper tubes, each 10-em long between the tube sheets. Calculate the steam condensation heat transfer coefficient for the tubes of this exchanger Calculate the rate of exchanger (10) a. vapor generation (kg/sec), m, in the tubes of this (10) a. 400 k 帛? 40...
A concentric tube heat exchanger of length L = 2 m is used to thermally process a pharmaceutical product flowing at a mean velocity of u_m,c = 0.1 m/s with an inlet temperature of T_c,i = 20 degree C. The inner tube of diameter D_i = 10 mm is thin walled, and the exterior of the outer tube (D_0 = 20 mm) is well insulated. Water flows in the annular region between the tubes at a mean velocity of u_m,h...
6 Water is heated in a pipe by exchanging heat with a warmer fluid that flows outside the pipe. Inside diameter of the pipe is dn 0.045 m and outside diameter dour0.05 m. Mean velocity of the water in the pipe is um-0.31 m/s and the bulk temperature is 323 K (density 988 kg m-3; viscosity 0.00055 kg m' sı. Pr 3.56, thermal conductivity k 0.64 W m1 Kt). The material of the pipe has thermal conductivity k 0.61 W...
Required information A shell-and-tube heat exchanger is used for cooling 47 kg/s of a process stream flowing through the tubes from 160°C to 136°C. This heat exchanger has a total of 100 identical tubes. each with an inside diameter of 2.5 cm and negligible wall thickness. The average properties of the process stream are: p = 950 kg/m”, k = 0.50 W/mK, Cp=3.5 kJ/kg.K, and -20 mPas The coolant stream is water (cp=4.18 kJ/kg K) at a flow rate of...
Most questions answered within 3 hours.
-
When an object moves through a fluid, the fluid exerts a viscous
force F on the...
asked 39 minutes ago -
Why did the observed chemistry of thallium mislead Mendelev to
place the group 13 element (Tl)...
asked 1 hour ago -
A sine wave signal is displayed on the screen of an
oscilloscope. 6 peak-to-peak divisions are...
asked 4 hours ago -
a
1500 kg car accelerates from 0 to 25 m / s in 21.0s. How much...
asked 5 hours ago -
Calculate the molarity of each of the following solutions:
(a) 30.5 g of ethanol (C2H5OH) in...
asked 5 hours ago -
1 Refer to the build-borrow-or-buy framework as a decision tree
for the Adidas company. Identify a...
asked 5 hours ago -
Problem 2: The Problem of Social Cost. A Rancher and Farmer live
side-by-side to each other....
asked 7 hours ago -
a uniform bar of weight 40N is 4 meter long. weights
on 60N and 100N are...
asked 6 hours ago -
Define Diet counceling? What are the
responsibilities of a counselor?
asked 8 hours ago -
Hey im just confused about how to put the ' A angle n' and ' S...
asked 8 hours ago -
A short essay about the WSJ article on Oreo versus Hydrox.
asked 8 hours ago -
##8. A program contains the following function definition:
##def cube(num):
##return num * num * num...
asked 8 hours ago