We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
9) What is the minimum output voltage for this clamping circuit? +10 h -10 U 1.0V...
In a full wave bridge rectifier, input voltage is 110sin(2pi60t) V, Vd=0.7V. The transformer turn ratio is 10:1. What is the amplitude of output voltage? What is the maximum voltage across diode which is off? For load of 5kohm, calculate C for Vr of 1V.
5000 10.2 S pts) The Zener diode in the circuit on the right voltage V 20 = 8.5V., and Zener resistancerz the circuit on the right has a Zener d) Find the Thevenin equivalent circuit as seen by lo b) Find the output voltage if a loa Find the output voltage if a load R, is connected and it draws a 1.5 mA current. Determine the value of RL c) How small can the load R, be, while ensuring that...
The zener diode in the circuit below has voltage Vzo = 5V, Iz = 0. It is modeled as a 0.7V drop in the forward direction. a) Determine the value of resistor R, that would result in a DC current 10 = 1 mA. b) Determine the DC output voltage V c) The circuit is subjected to a +-7V square wave as shown below. Capacitor Cis chosen such that at the square wave frequencies it acts as a short circuit....
11) 20pts. The zener limiter circuit s V R often used as a low power voltage regulator for a DC power supply. This circuit is an example in load A) Find R so that the maximum power dissipated in the zener diode is Po for any possible value of Road given P, Vin and B) What is the maximum current that the load can draw before the zener stops regulating the voltage? C) When the circuit is regulating the voltage...
2.19 Consider the circuit shown in Figure P2.19. The Zener diode voltage is Vz = 3.9 V and the Zener diode incremental resistance is ra = 0. (a) Deter- mine Iz, Il, and the power dissipated in the diode. (b) Repeat part (a) if the 4 k 32 load resistor is increased to 10 KS2. 12 k22 " 1112 vz$ 111 462 20 v= Figure P2.19
4. Design a clamp circuit to clamp the negative extreme of a periodic input waveform of 10 sin(100πt)V to −5 V. Use 1 diode, 1 Zener diode, 1 resistor, and 1 capacitor of suitable values. Provide following minimum ratings of the selected components. (a) Diode - Maximum reverse voltage, peak forward current (b) Zener - Zener voltage, Zener current (c) Resistor - Resistance, power rating (d) capacitor - capacitance, Maximum voltage Assume a 0.6 V forward drop for all diodes...
that's all information it gives A zener-diode voltage regulator circuit is shown below. The tage V 8.0V and the zener resistance is assumed to Problem 3: (20 points) zener diode has breakdown vol be 0 ohms. The power supply voltage Vps can vary between resistance RL can vary between 100 ohms and 1 kohm. 10V and 14V and the load Ri PS 1. Find a value of Ri such that the zener diode remains properly biased over the range of...
w A ovo 3. (15 pts) The input Vg to the rectifier circuit on the right is a sinusoidal signal of amplitude 4V, as shown below. Use the 0.7V voltage drop model for the diode. a) Determine the maximum and minimum values of the output voltage V across load resistor RL. b) Determine the conduction angle. c) Determine the percent conduction. 10022 {RL 2002 3. (15 pts) The input to the rectifier circuit on the right is sinusoidal signal of...
10. Topic: The Zener Diode (variable load regulation) Problem: Using the supplied datasheet, determine the minimum and the maximu voltages that can be regulated by the Zener diode in the following circuit. 220 N4739A ou Vin Max. Zener Impedance Leakage Current VR Device Min. Typ. Max.Iz (mA) A 3315 3.6 4.3 4845 S1 IN4729A N4730A3705 39 4096 N4731A4085 4515 4.935 4.465 1N4733A IN4734A IN4735A IN4736A 1N4737A IN4738A IN4739A 8.645 N4740A 651 7.14 7.875 41 5.89 6.46 7.79 9.5 7.5 31...
(a) The following circuit shows a linear voltage regulator. Assuming the zener diode has specifications (VZ = 2.5 V, IZ = 60 mA), select adequate resistor values to provide a regulated output voltage Vo = 10 V from an unregulated voltage Vi = 15V. (b) Calculate the power efficiency of the regulator when a load RL = 10Ω is connected to the regulator output. (c) Briefly explain the terms “dropout”, “line regulation”, and “load regulation”, as they apply to voltage...