Torsion

Question

Question

A 10m solid steel Shaft is subjected to a torque of 15kNm resulting an angel of twist of 4° from its original position.given G= 85GPa.calculate

Answer 1

Similar Homework Help Questions

TORSION

a) A hollow circular shaft designed to have an inner diameter of 0.7Do; where Do is an outer diameter.i) Determine the inner and outer diameters of the shaft if the maximum allowable shearing stress is Y0 N/mm2 and torque is X00 kNm. Then, calculate the polar moment of inertia.ii) By using inner diameter calculated in (i), calculate the maximum shearing stress and a new torque, if the shaft is changed to solid circular shaft. The shaft is 1.5 m long with the twisted through...
In all the questions below, the material is structural steel with or= 220 MPa, E =...

In all the questions below, the material is structural steel with or= 220 MPa, E = 200 GPa, v=0.3, and a = 12x10-6/°C. Question 1 The steel shaft in Figure 1 is subjected to the torques shown. Calculate: 1. The maximum torque (Tmax) that can be applied for the shaft to operate with a safety margin of 30% (Tresca). 2. The resulting angle of twist of plane B relative to A 3. The resulting angle of twist of plane C...
A. What is the minimum diameter of a solid steel shaft that will not twist through...

A. What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6-m length when subjected to a torque of 12 kN·m? Use G = 83 GPa. B. Determine the bearing stress of the punch out plate of the precious problem, Answer in MPa

A. What is the minimum diameter of a solid steel shaft that will not twist through...

A. What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6-m length when subjected to a torque of 12 kN·m? Use G = 83 GPa. B. What maximum shearing stress is developed? C. Determine the bearing stress of the punch out plate of the precious problem, Answer in MPa
please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity...

please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
Exercises: What is the minimum diameter of a solid steel shaft that will not twist through...

Exercises: What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6m length when subjected to a torque of 14 kN-m? What maximum shearing stress is developed? Use G = 83 Gpa Required: d = ? Given: 0 = 30 L = 6m T = 14 kN-m G = 83 GPa Tmax= ?

In all the questions below, the material is structural steel with or= 220 MPa, E =...

In all the questions below, the material is structural steel with or= 220 MPa, E = 200 GPa, v=0.3, and a = 12x10-6/°C. Question 1 The steel shaft in Figure 1 is subjected to the torques shown. Calculate: 1. The maximum torque (Tmax) that can be applied for the shaft to operate with a safety margin of 30% (Tresca). 2. The resulting angle of twist of plane B relative to A 3. The resulting angle of twist of plane C...
(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N·m from the engine to the generator. Determine the angle of twist (0) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa.
(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T=524 N·m from the engine to the generator. Determine the angle of twist (%) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa. (10 points)