Homework Answers
solution
Add Answer to:
A radial water pump with an exit radius of 5 in. an exit blade thickness of...
Please answer question 7: A centrifugal pump discharges 500 GPM through a 12-inch diameter impeller. The fluid...
Please answer question 7:
A centrifugal pump discharges 500 GPM through a 12-inch diameter
impeller. The fluid leaves the impeller with a
tangential velocity of 17 ft/sec. If water, @ 68°F,
enters the impeller via radial flow (I.E. no whirl), and the inner
radius and thickness of the impeller are
1.75-inches. (Assume a constant thickness of the
impeller) and if the pump speed is 1775 rpm, with a head loss of
4.5-feet. What is the horsepower input to the flow by
the pump?
QUESTION...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter of intake pipe = 160 mm; entrance losses = one velocity head in suction pipe; required NPSH = 42 kPa; water temperature = 30°C N D1, D2 : inlet and outlet diameters of impeller (rotor) b : impeller width 0,6 : inlet and outlet impeller vane angles (degrees) : speed of rotation of impeller (and its driver) in rpm V, V :tangential and radial...
HELPPPP 5 Hydraulic Press ●4 11.0 ft Flow 10.0 ft 2.0 ft 1 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press. The following is known: The volume...
HELPPPP
5 Hydraulic Press ●4 11.0 ft Flow 10.0 ft 2.0 ft 1 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press. The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 and v-4.30X10+ ft'/s. The power input to the pump is 20 hp. . The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and efficiency curves that can be characterized by the following dimensionless equations: Pump head 6 = 6.04-1616 where and 5 nD Pump efficiency n = 705-91,5006 where n = (power to water) / (elect power input) In the above equations, is the dimensionless pump head and is the dimensionless volumetric flow rate. h, is the pump head, n is the pump shaft/impeller rotation rate, and...
Hydraulic Press 11.0ft Flow 10.0 ft 2.0ft 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press The following is known: The volume flow rate is...
Hydraulic Press 11.0ft Flow 10.0 ft 2.0ft 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 The power input to the pump is 20 hp. The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85 based on the velocity head in the suction line All...
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-250...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
please solve 5(b) and 6 (a and b) fluid machinery b)An inward flow reaction turbine works under a head of 100m. The inlet and outlet diameters of the runner are 1.2 m and 0.6 m, respectively. The...
please solve 5(b) and 6 (a and b) fluid machinery
b)An inward flow reaction turbine works under a head of 100m. The inlet and outlet diameters of the runner are 1.2 m and 0.6 m, respectively. The width of the runner is 150 mm, which is constant throughout. The velocity of flow at the outlet is 6 m/s. The blade angle at the outlet is 15. The hydraulic efficiency is 0.9. Calculate the following: ) The speed of the Turbine...
(100 points) Water at 25°C is pumped at a rate of 0.075m'/s from a reservoir 20m above a pump to a free di...
(100 points) Water at 25°C is pumped at a rate of 0.075m'/s from a reservoir 20m above a pump to a free discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of 5in diameter cast iron. From the pump to the discharge the pipe is...
L2 r. cunhinning moncones the spood of piston at the hepinning of the stonke in the...
L2 r. cunhinning moncones the spood of piston at the hepinning of the stonke in the cylinder cushimin decrees the speed of piston ot the beginning of the role in the und 2) Which Type of bydraulic finder has one piston connected to piston rud extended on both the a female clevis 1. Circular fans c. Trunnion all of the above Which of the following is used for mounting purpose in luydraulic cylinders? sides of the cylinder! 3. telescopic cylinder...
Water at 50 °F is pumped from pond 1 to pond 2. Calculate the volumetric flow...
Water at 50 °F is pumped from pond 1 to pond 2. Calculate the volumetric flow rate and pump power for the following given information Patm h Opump Patm ... Total pipe length: /=500 ft Pipe diameter: d=8 in Pipe material: new cast iron Elbow type: flanged, 90° regular Valve type: globe, flanged, fully open Inlet and Exit type: sudden, Fig. 6.22 Pump head: hp 250 ft Pump efficiency: np=0.85 h-200 ft F (velocity, ft/s x diameter. (Vd) for water...
Please answer question 7:
A centrifugal pump discharges 500 GPM through a 12-inch diameter
impeller. The fluid leaves the impeller with a
tangential velocity of 17 ft/sec. If water, @ 68°F,
enters the impeller via radial flow (I.E. no whirl), and the inner
radius and thickness of the impeller are
1.75-inches. (Assume a constant thickness of the
impeller) and if the pump speed is 1775 rpm, with a head loss of
4.5-feet. What is the horsepower input to the flow by
the pump?
QUESTION...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter of intake pipe = 160 mm; entrance losses = one velocity head in suction pipe; required NPSH = 42 kPa; water temperature = 30°C N D1, D2 : inlet and outlet diameters of impeller (rotor) b : impeller width 0,6 : inlet and outlet impeller vane angles (degrees) : speed of rotation of impeller (and its driver) in rpm V, V :tangential and radial...
HELPPPP
5 Hydraulic Press ●4 11.0 ft Flow 10.0 ft 2.0 ft 1 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press. The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 and v-4.30X10+ ft'/s. The power input to the pump is 20 hp. . The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85...
Project-Design Problem: A family of water pumps produced by a given pump manufacturer have performance and efficiency curves that can be characterized by the following dimensionless equations: Pump head 6 = 6.04-1616 where and 5 nD Pump efficiency n = 705-91,5006 where n = (power to water) / (elect power input) In the above equations, is the dimensionless pump head and is the dimensionless volumetric flow rate. h, is the pump head, n is the pump shaft/impeller rotation rate, and...
Hydraulic Press 11.0ft Flow 10.0 ft 2.0ft 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 The power input to the pump is 20 hp. The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85 based on the velocity head in the suction line All...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
please solve 5(b) and 6 (a and b) fluid machinery
b)An inward flow reaction turbine works under a head of 100m. The inlet and outlet diameters of the runner are 1.2 m and 0.6 m, respectively. The width of the runner is 150 mm, which is constant throughout. The velocity of flow at the outlet is 6 m/s. The blade angle at the outlet is 15. The hydraulic efficiency is 0.9. Calculate the following: ) The speed of the Turbine...
(100 points) Water at 25°C is pumped at a rate of 0.075m'/s from a reservoir 20m above a pump to a free discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of 5in diameter cast iron. From the pump to the discharge the pipe is...
L2 r. cunhinning moncones the spood of piston at the hepinning of the stonke in the cylinder cushimin decrees the speed of piston ot the beginning of the role in the und 2) Which Type of bydraulic finder has one piston connected to piston rud extended on both the a female clevis 1. Circular fans c. Trunnion all of the above Which of the following is used for mounting purpose in luydraulic cylinders? sides of the cylinder! 3. telescopic cylinder...
Water at 50 °F is pumped from pond 1 to pond 2. Calculate the volumetric flow rate and pump power for the following given information Patm h Opump Patm ... Total pipe length: /=500 ft Pipe diameter: d=8 in Pipe material: new cast iron Elbow type: flanged, 90° regular Valve type: globe, flanged, fully open Inlet and Exit type: sudden, Fig. 6.22 Pump head: hp 250 ft Pump efficiency: np=0.85 h-200 ft F (velocity, ft/s x diameter. (Vd) for water...
Most questions answered within 3 hours.
-
D. A student completed 20 courses in the School of Arts and
Sciences. Her grades in...
asked 1 hour ago -
teo
pucks moving on a frictionless air table are about to collide. the
1.5 kg puck...
asked 1 hour ago -
Problem #1
The area between Z = 0 and Z = 2.50
The area between Z...
asked 3 hours ago -
1. What is the meaning of the term communication style?
2. What are the benefits to...
asked 2 hours ago -
9.) You are buying a car that cost $26,500. You make payments of
$412 each month...
asked 3 hours ago -
. Suppose a discrete random variable has probability
distribution
P(x) = .2 if x = 0...
asked 4 hours ago -
Under the influence of its drive force, a snowmobile is moving
at a constant velocity along...
asked 4 hours ago -
Why do organizations decline? What steps can top
management take to halt, decline, and restore organizational...
asked 4 hours ago -
What mechanisms Drive speciation??
(I.e. what was Dawins theory on the orgin of species, and how...
asked 6 hours ago -
The manager at a car assembly plant believes that the mean
assembly time for a car...
asked 7 hours ago -
Which of the following is true of electron capture?
A) It decreases the nuclide's mass number...
asked 8 hours ago -
Assuming an efficiency of 43.10%, calculate the actual yield of
magnesium nitrate formed from 114.9 g...
asked 9 hours ago