11. For the network below containing a voltage controlled current source, find the current through, voltage...
current controlled voltage source 2i R2 V3 EV1 V2 R1 In the circuit above V1 = 86V,V2=96 V, 11-7AR1:39 ? and R2 : 35 ?. Use nodal analysis to find the voltage at node A in the circuit above. Note the presence of a dependent voltage source V3 Voltage across that source is 2i. i is the current through the resistor R2 and the source V2
For the DC cicuit show below, find the voltage and current across each resistor. The voltage source is 40V. Find the power dissipations in R1 and R3. Click on the circuit to view a larger image 20 , RB 500 2, Rc RA 400 , and Rp 75 - - Current through RA A Voltage drop across RA V Power dissipation in RA W Current through Rg A Voltage drop across R V Current through Rc = A Voltage drop...
Q1: Use Mesh analysis to find the following a. The current passing through the 11 resistor. b. The voltage across the 2 resistor. c. The power dissipated at 4 resistor. 20 40 3100
Q4/// What is the current of the 40 v ?voltage source of the circuit below SA 202 w 802 w 103 40 20 V 40 V Current source Voltage source leave question o 13 A 0.5 A O 12A O 10 A 1A O أخرى: Q5/// The maximum power dissipated in a 4 load is 100 w when connected to a d.c. voltage V and internal resistance R. Calculate: the current in the load, internal *.resistance R, and voltage V...
P1 (25 pts): Find the current supplied by the 48 V source, as well as the current through each of the resistors and the voltage drop across each resistor. R, 20入そk2 P2 (25 pts): The voltage across RB is found to be 15 V. What current must be supplied by the source? What must be the voltage drop across RA and Rc? What must be the voltage supplied by the source (that is, what is Vi)? RA 5032
to create a circuit which drives a controlled current through an LED with an input voltage, Vref.The design performed here is a low power circuit (at most 15 mA ows through the LED) which will be scaled up to a high powered version (300 mA) for your major project. The voltage drop across the resistor should be large enough for the feedback voltage to not be signicantly e ected by noise. The resistance should be large enough for parasitic resistance...
All of them have short answers. 1. If a 19.9mA current source, a 32.6kΩ resistor, a 49.6kΩ resistor and a 42.6kΩ resistor are all connected in parallel, then what is the current through the 42.6kΩ resistor in milliamps? 2. If a 8.9V voltage source is applied across a 43.6kΩ resistor connected in series with a 25.3kΩ resistor, then what is the voltage across the 25.3kΩ resistor in volts? 3. If the Thevenin equivalent for a circuit is a 5.5V voltage...
Circuits The table beside circuit a below shows the current through each resistor, the voltage across each resistor, and the power dissipated as heat in each resistor. Find the similar correct value for circuits b, c, and d, and put your answers in the tables shown.
33. (10 pt.) Refer to the diagram below. +5V Source: Circuit Lab procedure ENGR1182 a) Calculate total resistance. b) Calculate the electric potential difference for the 1000-Ω resistor. c) Calculate the power dissipated by the 100-2 resistor d) Calculate the power delivered by the source. e) What is the voltage across the 100-2 resistor? f) What is the voltage across the 1000-Q resistor? g) What is the current through the 100-2 resistor? h) What is the current through the 1000-Q...
6.39 Let vg represent the voltage across the current source in the circuit in Fig. 6.29. The reference for vg is posi- tive at the upper terminal of the current source. a) Find vg as a function of time when , = 16-16e-51 A. b) What is the initial value of vg? c) Find the expression for the power developed by d) How much power is the current source develop- e) Calculate the power dissipated in each resistor the current...