Homework Answers
Add Answer to:
Prob5 A venture meter having a throat diameter of 150 mm is installed in a horizontal...
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter...
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter is 90 mm. One static pressure tapping is located at the throat and another 0.3 m upstream in the pipeline. The pressure difference measured between the two tappings is 200 mm of mercury. The coefficient of discharge for the meter is 0.97. Determine the actual...
VENTURI METER Problem 6 - 44 A vertical Venturi meter, 150 nm in diameter is connected...
VENTURI METER Problem 6 - 44 A vertical Venturi meter, 150 nm in diameter is connected to a 300-mm diameter pipe. The vertical distance from the inlet to the throat being 750 nm. If the deflection of mercury in the differential manometer connected from the inlet to the throat is 360 mm, determine the flow of water through the meter if the meter coefficient is 0.68. Determine also the head lost from the inlet to the throat 750 mm 360...
A venturi meter with a diameter of 30 cm at the entrance and 15 cm at...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
Short Answer A venture tube tapers from 400 mm in diameter at the entrance to 200...
Short Answer A venture tube tapers from 400 mm in diameter at the entrance to 200 mm in diameter at the throat; the discharge coefficient is 0.98. A differential mercury U-tube gauge is connected between pressure tapping at the entrance at throat. If the meter is used to measure the flow of water and the water fills the leads to the U-tube and is in contact with the mercury, calculate the discharge when the difference of level in the U-tube...
A vertical venturi-meter is connected to a vertical pipe which carries water as shown in the...
A vertical venturi-meter is connected to a vertical pipe which carries water as shown in the figure. the diameters at the entrance and throat are 150 mm and 75 mm, respectively. The the mercury (specific gravity +13.6). U-tube mercury manometer connected to the entrance and throat of the meter . the height difference between the throat and entrance is 150mm.If the actual rate is 40 liters/s and the coefficient of discharge is 0.96, calculate (a) the pressure difference between entrance and...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
fluid Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at...
fluid
Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at 40° to the horizontal to measure the flow rate of petrol having a specific gravity of 0.8. The ratio of areas of main pipe and throat is 5 and the throat is at 1 m from the inlet along its length. The difference in manometer head is 40 mm of mercury. Assuming the coefficient of discharge as 0.96. Calculate the discharge through the venture...
Venturi meter provided in a vertical pipeline carries oil of specific gravity 0.88 as shown in...
Venturi meter provided in a vertical pipeline carries oil of specific gravity 0.88 as shown in the Figure below. The diameter at the entrance and throat are 30 cm and 15 cm, respectively. A U-tube manometer filled with mercury of density 13600kg/m3 is connected to the entrance and throat of the meter . The height difference between the throat and entrance is 30cm. if the actual flow rate is 80 L/s and the coefficient of discharge of the meter is...
Ans. 6.29 ft3/s (B) 5./ A venturi meter with a diameter of 6 in at the...
Ans. 6.29 ft3/s
(B)
5./ A venturi meter with a diameter of 6 in at the oat is installed in an 18 in water main. A differential manometer gauge is partly filled with mercury (the re- mainder of the tube is filled with water) and connected to the meter at the throat and inlet. The mercury col- umn stands 15 in higher in one leg than in the other. Neglecting friction, what is the flow through the meter? The specific...
In a laboratory experiment, an orifice of diameter 15 mm is installed in a 25 mm...
In a laboratory experiment, an orifice of diameter 15 mm is installed in a 25 mm diameter pipe and two pressure tappings, one before and one after the orifice, are connected to a vertical mercury manometer. The discharge is obtained by measuring the rise of water level in a 30 cm x 30 cm square tank collecting the outflow from the pipe. For a particular experiment, the difference in manometer readings was 130 mm of H level was 120 mm...
(c) A venturi meter is mounted in a pipeline of diameter 150 mm, which is inclined at 30° from the horizontal. Water is flowing upwards through the pipeline. The throat diameter of the venturi meter is 90 mm. One static pressure tapping is located at the throat and another 0.3 m upstream in the pipeline. The pressure difference measured between the two tappings is 200 mm of mercury. The coefficient of discharge for the meter is 0.97. Determine the actual...
VENTURI METER Problem 6 - 44 A vertical Venturi meter, 150 nm in diameter is connected to a 300-mm diameter pipe. The vertical distance from the inlet to the throat being 750 nm. If the deflection of mercury in the differential manometer connected from the inlet to the throat is 360 mm, determine the flow of water through the meter if the meter coefficient is 0.68. Determine also the head lost from the inlet to the throat 750 mm 360...
A venturi meter with a diameter of 30 cm at the entrance and 15
cm at the throat, is connected to a vertical pipe of diameter 30cm
carrying oil of specific gravity 0.9. The difference in elevation
of the throat section and the entrance of the venturi meter is 30
cm. The mercury manometer shows a gauge deflection of x =
1000mm.
Determine
1) the discharge of oil; and
2) the pressure difference between the entrance section and
throat section....
Short Answer A venture tube tapers from 400 mm in diameter at the entrance to 200 mm in diameter at the throat; the discharge coefficient is 0.98. A differential mercury U-tube gauge is connected between pressure tapping at the entrance at throat. If the meter is used to measure the flow of water and the water fills the leads to the U-tube and is in contact with the mercury, calculate the discharge when the difference of level in the U-tube...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
fluid
Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at 40° to the horizontal to measure the flow rate of petrol having a specific gravity of 0.8. The ratio of areas of main pipe and throat is 5 and the throat is at 1 m from the inlet along its length. The difference in manometer head is 40 mm of mercury. Assuming the coefficient of discharge as 0.96. Calculate the discharge through the venture...
Ans. 6.29 ft3/s
(B)
5./ A venturi meter with a diameter of 6 in at the oat is installed in an 18 in water main. A differential manometer gauge is partly filled with mercury (the re- mainder of the tube is filled with water) and connected to the meter at the throat and inlet. The mercury col- umn stands 15 in higher in one leg than in the other. Neglecting friction, what is the flow through the meter? The specific...
In a laboratory experiment, an orifice of diameter 15 mm is installed in a 25 mm diameter pipe and two pressure tappings, one before and one after the orifice, are connected to a vertical mercury manometer. The discharge is obtained by measuring the rise of water level in a 30 cm x 30 cm square tank collecting the outflow from the pipe. For a particular experiment, the difference in manometer readings was 130 mm of H level was 120 mm...
Most questions answered within 3 hours.
-
What are the negative effects of abruptly stopping the use of
all fossil fuels? Give at...
asked 17 seconds from now -
Given that many conflict are the result of different parties having
different interests, is it possible...
asked 4 minutes ago -
A 750 g block can slide uniformly along the horizontal track
when a string attached to...
asked 7 minutes ago -
In 2017, Juan entered into a contract to write a book. The
publisher advanced Juan $50,000,...
asked 21 minutes ago -
Determine the number of kinds of protons in each molecule (w/
respect to NMR spectroscopy). Drawing...
asked 31 minutes ago -
A jeweler whose near point is 68 cm from his eye uses a
magnifying glass as...
asked 29 minutes ago -
A company wants to determine how many units of each of two
products, A and B,...
asked 33 minutes ago -
The blood pressure of a person changes throughout the day.
Suppose the systolic blood pressure of...
asked 42 minutes ago -
A chemistry student desired to study sulfur. Sulfur exhibited
the following characteristics with oxygen:
(a) It...
asked 37 minutes ago -
An Atwood machine is constructed of a solid-disk frictionless
pulley of mass m3 and radius R....
asked 39 minutes ago -
what are the advantages of lanthanum hexaboride over tungsten
filament for electron emission
what is the...
asked 41 minutes ago -
Question 5
Your uncle offers to sell you his vintage Rolls Royce. He
suggests a payment...
asked 46 minutes ago