Air flows into the atmosphere from a nozzle and strikes a vertical plate as shown in below figure. The reading on the pressure gage was 1.82 kPa. Determine the horizontal force required to hold the plate in place. Assume the flow to be incompressible and frictionless. Also consider the density of air is 1.23 kg/m3 and neglect the air weight.
Air flows into the atmosphere from a nozzle and strikes a vertical plate as shown in...
Air flows into the atmosphere from a nozzle and strikes a vertical plate as shown in below figure. The reading on the pressure gage was 1.82 kPa. Determine the horizontal force required to hold the plate in place. Assume the flow to be incompressible and frictionless. Also consider the density of air is 1.23 kg/m² and neglect the air weight. P-1.82 kPa F-IN A-0.003 m A-0.01 m
g through a nozzle. The inlet pressure is p 3.7 kPa (gage) air flowing and the air exhausts into the atmosphere. The nozzle has an inlet diameter of 60 mm and an exit diameter of 10 mm, and the nozzle is connected to the supply pipe by flanges. Find the force required to hold the nozzle stationary. Assume the air has a constant density of 1.22 kg/m Neglect the weight of the nozzle. m Flanges Flow 2 g through a...
5.26 A nozzle is attached to a vertical pipe and discharges water into the atmosphere as shown in Fig. P5.26. When the discharge is 0.1 m/s, the gage pressure at the flange is 40 kPa. Determine the vertical component of the anchoring force required to hold the nozzle in place. The nozzle has a weight of 200 N, and the volume of water in the nozzle is 0.012 mº. Is the anchoring force directed upward or downward? 300 Area =...
Air flows into the atmosphere f pressure gage. Assume the fow to be incompressible and frictioniess. and strkes a vertical plate as shown in the figure below. A horizontal force of 9 N is required to hold the plaete in place. Determine the reading on the p-? Area 0.003 m2 Area-001 m2 dy Control volume analysis concepts Momentum fux is a result of fuld motion across the control surface. External forces, including surface forces and body forces act on a...
2.) Water from a stationary nozzle strikes a flat plate as shown below. The water leaves the nozzle at 15 m/s; the nozzle area is 0.01 m2. Assuming the water is directed normal to the plate, and flows along the plate, determine the horizontal for on the support. FLOW -Plate 6 NEPLE
i need clear writing please 1) Water from a stationary horizontal nozzle strikes a lat plate which is aligned at 30 from the vertical. 70% of the flow exits past the upper side of the plate and 30% the lower. Water leaves the nozzle at 15 m/s, and the area of the nozzle is 0.1 m2. The flow of the water is along the plate. It was determined that the area of the flow leaving the upper side of the...
Consider water flowing through a converging channel as shown and discharging freely to the atmosphere at the exit. What is the gage pressure at the inlet? Assume the flow to be incompressible, and neglect any frictional effects. D, = 150 mm D2 = 75 mm V1 = 1.2 m/s P2 = Patm %3D (A) 10.2 kPa (B) 10.8 kPa (C) 11.3 kPa (D) 12.7 kPa
1 (a) A steady stream of water jet discharges from the nozzle with a uniform velocity of 10 m/s at angle 60° as shown in Figure 1. The jet strikes a horizontal plate 2 m above the nozzle exit. Upon impact, part of the flow is guided towards the left while the remainder towards the right, and the plate is suspended in the air. The weight of the plate is 25 N. Assume frictionless flow along the plate and weight...
Show all work and answer all parts of the problem please. The 45 degree elbow nozzle discharges water into the atmosphere. The cross-sectional area of the elbow is 25 cm2 150 cm2 at the inlet and 25 cm2 at the exit. Velocity at point 1 and 2 are given as 2 m/s and 12 m/s 450 respectively. The gage pressure at 1 is 73 kPa 150 em2 30 cm The elevation difference between the centers of the exit and the...
Water at 60 °F flows through the elbow as shown below and is then injected to the atmosphere through a nozzle (on a horizontal plane). The pipe diameter is Di = 4 in. while the diameter of the exit of the nozzle is D2 = 1 in. At a flow rate of Q = 245 gpm, the gage pressure at the section (1) where the flange locates is Pi = 34 psig. Neglect the weight of the water and elbow,...