Homework Answers
Problem No-3: Air at 20 c(p-1.21kg/mH-38x107 kg.m/s) and with a free stream velocity o 40 m/s...
Problem No-3: Air at 20 c(p-1.21kg/mH-38x107 kg.m/s) and with a free stream velocity o 40 m/s flows past a smooth thin plate which is 3-m wide and 10-m long in the flow direction. turbulent boundary layer from the leading edge determine: (a) the boundary layer thickness 6 m from the leading edge (b) the drag coefficient and drag force exerted by the fluid on the thin plate Take density 1.2 kg/m3 and kinematic viscosity as 1.49 x 10-s m'/s: (12p)...
Exercise 2 Air at 20 °C and 1 atm flows over a flat plate at 50...
Exercise 2 Air at 20 °C and 1 atm flows over a flat plate at 50 m/s. The plate is 300 cm long and is maintained at 60C. The width of the plate is 2 m. The critical Rec = 5 x 105 The properties are Conductivity k = 0.0263 W/mK, kinematic viscosity nu = v = 15.89 x 10-6 m²/s, Prandtl number is Pr=0.707 Density rho = p = 1.128 kg/m3 1. Determine the critical length Xc 2. Determine...
Required information Air at 25°C and 1 atm is flowing over a long flat plate with...
Required information Air at 25°C and 1 atm is flowing over a long flat plate with a velocity of 7 m/s. The density and kinematic viscosity of air at 1 atm and 25°C are p= 1.184 kg/m3 and V = 1.562x10-5 m2/s. Calculate the distance from the leading edge of the plate where the flow becomes turbulent. The distance from the leading edge of the plate is m. Required information Air at 25°C and 1 atm is flowing over a...
Air at T=25°C and pressure P=1 bar flows over a square plate with a velocity V=1...
Air at T=25°C and pressure P=1 bar flows over a square plate with a velocity V=1 m/s. This plate has a length L= 1 m and it is heated over its entire length; the plate temperature is constant Tp=100°C. The following data are given. For air: dynamic viscosity: mu = 1.9*10–5 kg/(m.s); density: rho = 1.05 kg/m3; conductivity k = 0.03 W/(m K); Specific heat Cp = 1.007 kJ/(kg K); Prandtl number Pr = 0.7 For laminar flow over a...
5. A fan that can provide air speeds up to 30 m/s is to be used...
5. A fan that can provide air speeds up to 30 m/s is to be used in a low-speed wind tunnel with atmospheric air at 23°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behavior up to a Reynolds number of 107, what is the minimum plate length that should be used? At what distance from the leading edge would transition occur if the critical Reynolds number was Re.c-5 × 105?
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
Consider air flows with velocity of U?=U= 10 m/s over a semi-finite smooth flat plate with...
Consider air flows with velocity of U?=U= 10 m/s over a
semi-finite smooth flat plate with L=97 cm long. Calculate the
followings by assuming ? = 1.568 x 10-5 m2/s and ?=1.177
kg/m3.
Figure 1 : Boundary layer over a flat plate
Consider air flows with velocity of U?=U=10 m/s over a
semi-finite smooth flat plate with L=97 cm long. Calculate the
followings by assuming ? = 1.568 x 10-5 m2/s and ?=1.177
kg/m3.
b) Under some flow and boundary...
Problem 4 Air at 100 C flows across a thin, flat plate of subliming naphthalene that...
Problem 4 Air at 100 C flows across a thin, flat plate of subliming naphthalene that is 3.4 m long. The Reynolds number at the trailing edge of the plate is at the upper limit for a laminar boundary layer (Re 5e5). Estimate: (a) the average rate of sublimation in kmol/s*m2; and (b) the local rate of sublimation 0.5 m from the leading edge. Vapor pressure of naphthalene = 10 torr viscosity of air 0.0215 cP; molar density of air...
Air with a dynamic viscosity of 18.1 x 10 N m/s, a density of 1.2 kg/m'...
Air with a dynamic viscosity of 18.1 x 10 N m/s, a density of 1.2 kg/m' and a free stream velocity of 20 m/s flows over a 0.8 m long by 0.3 m wide flat plate. 20 m/s -0.5 m - -0.8 m a. Find the type of flow on flat plate based on Reynolds number b. Find the boundary layer thickness at distance of 0.5 m from the leading edge c. Find the wall shear stress at a horizontal...
density (kg/m) viscosity (cp mPa s) VISCOsI water 20°C air 20°C 1000 1.204 1090 1.03 02217...
density (kg/m) viscosity (cp mPa s) VISCOsI water 20°C air 20°C 1000 1.204 1090 1.03 02217 250,000 eanut butter Paper Homework 3 Viscosity and Flow. Learning Objectives: 1. Gain a feel for the Reynolds number for typical situations. 2. Determine type of flow from the Reynolds number. Calculate the Reynolds number, Re - (2rpv)/ n, for the following situations and decide whether the flow of fluid around them is laminar or turbulent. Then calculate the frag force using the appropriate...
Problem No-3: Air at 20 c(p-1.21kg/mH-38x107 kg.m/s) and with a free stream velocity o 40 m/s flows past a smooth thin plate which is 3-m wide and 10-m long in the flow direction. turbulent boundary layer from the leading edge determine: (a) the boundary layer thickness 6 m from the leading edge (b) the drag coefficient and drag force exerted by the fluid on the thin plate Take density 1.2 kg/m3 and kinematic viscosity as 1.49 x 10-s m'/s: (12p)...
Exercise 2 Air at 20 °C and 1 atm flows over a flat plate at 50 m/s. The plate is 300 cm long and is maintained at 60C. The width of the plate is 2 m. The critical Rec = 5 x 105 The properties are Conductivity k = 0.0263 W/mK, kinematic viscosity nu = v = 15.89 x 10-6 m²/s, Prandtl number is Pr=0.707 Density rho = p = 1.128 kg/m3 1. Determine the critical length Xc 2. Determine...
Required information Air at 25°C and 1 atm is flowing over a long flat plate with a velocity of 7 m/s. The density and kinematic viscosity of air at 1 atm and 25°C are p= 1.184 kg/m3 and V = 1.562x10-5 m2/s. Calculate the distance from the leading edge of the plate where the flow becomes turbulent. The distance from the leading edge of the plate is m. Required information Air at 25°C and 1 atm is flowing over a...
5. A fan that can provide air speeds up to 30 m/s is to be used in a low-speed wind tunnel with atmospheric air at 23°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behavior up to a Reynolds number of 107, what is the minimum plate length that should be used? At what distance from the leading edge would transition occur if the critical Reynolds number was Re.c-5 × 105?
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
Problem 4 Air at 100 C flows across a thin, flat plate of subliming naphthalene that is 3.4 m long. The Reynolds number at the trailing edge of the plate is at the upper limit for a laminar boundary layer (Re 5e5). Estimate: (a) the average rate of sublimation in kmol/s*m2; and (b) the local rate of sublimation 0.5 m from the leading edge. Vapor pressure of naphthalene = 10 torr viscosity of air 0.0215 cP; molar density of air...
Air with a dynamic viscosity of 18.1 x 10 N m/s, a density of 1.2 kg/m' and a free stream velocity of 20 m/s flows over a 0.8 m long by 0.3 m wide flat plate. 20 m/s -0.5 m - -0.8 m a. Find the type of flow on flat plate based on Reynolds number b. Find the boundary layer thickness at distance of 0.5 m from the leading edge c. Find the wall shear stress at a horizontal...
density (kg/m) viscosity (cp mPa s) VISCOsI water 20°C air 20°C 1000 1.204 1090 1.03 02217 250,000 eanut butter Paper Homework 3 Viscosity and Flow. Learning Objectives: 1. Gain a feel for the Reynolds number for typical situations. 2. Determine type of flow from the Reynolds number. Calculate the Reynolds number, Re - (2rpv)/ n, for the following situations and decide whether the flow of fluid around them is laminar or turbulent. Then calculate the frag force using the appropriate...
Most questions answered within 3 hours.
-
Fiscal policy is the deliberate manipulation of taxes and
government spending to alter GDP, employment, inflation...
asked 2 minutes ago -
Two concentric current loops lie in the same plane. The smaller
loop has a radius of...
asked 30 minutes ago -
1)Which of the following is an
important difference between qualified and nonqualified retirement
plans?
a. Qualified...
asked 42 minutes ago -
What's the streaming business's problem on the
horizon?
asked 1 hour ago -
I need help with writing the conclusion for this online lab
report
Abstract
By testing the...
asked 1 hour ago -
For the reaction 1N2+3H2-----> 2NH3, would the reaction rate
trend be: delta[NH3]/ delta t = -2...
asked 2 hours ago -
Within your current/past organization, identify a problem/issue
and format a design to address same. You may...
asked 2 hours ago -
A sock stuck to the side of a clothes-dryer barrel has a
centripetal acceleration of 24...
asked 3 hours ago -
A perfect gas undergoes an isentropic process such that its
volume doubles. If the ratio of...
asked 3 hours ago -
list the elements in groups 3A to 6A in the same order as in the
periodic...
asked 3 hours ago -
Estimating effect size. Peng and Chen (2014)
evaluated effect size estimates for various tests. In their...
asked 3 hours ago -
Write a script in MySQL that creates and calls a stored
procedure name test. This procedure...
asked 3 hours ago