Part A Head loss A gate valve is being used as a shut-off valve in a...
PartA The pipe system shown in (Figure 1) consists of a 3-in.-diameter, 100-ft-long galvanized iron pipe, a fully opened gate valve, four elbows, a flush entrance, and a pump with the pump head curve shown in (Figure 2). The friction factor is 0.022 Estimate the flow Express your answer using two significant figures gal/min Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ▼ Part B Estimate the corresponding pump head generated by the pump Express your...
Review The tank is filled with water at a temperature of 20°C. (Figure 1) Part A When the gate valve at C is opened, determine the flow through the 80-mm-diameter cast iron pipe. Include minor losses at the flush entrance, fully opened gate valve, and 90° elbow. Express your answer to three significant figures and include the appropriate units. PÅ RO 21 ? xoxo . x.10 Q- Value Units Figure < 1 of 1 > Submit Previous Answers Request Answer...
A 10-m-long, 5.042-cm I.D. copper pipe has two fully open gate valves, a swing check valve, and a sudden enlargement to a 9.919-cm I.D. copper pipe. The 9.919 cm copper pipe is 5.0 m long and then has a sudden contraction to another 5.042-cm copper pipe. Find the head loss for a 20 °C water flow rate of 0.05 m3/s.. Answer is 180
what is the velocity head at the inlet pump? Find the value of head loss (consider entrance, friction, elbow and valve losses). Also, find pressure at the inlet pump water is at 80 degrees C Water is being pumped from the tank at a rate of 475 L/min -115 m E Pump Globe valve fully open DN 65 Schedule 40 steel pipe 1.40 m 0.75 m Standard elbows (2)
The sewer pipe, made of unfinished concrete, is required to carry water at 45 ft/s when it is half full. The downward slope of the pipe is 0.0015. (Figure 1) Part A Determine the required internal radius of the pipe. Express your answer using three significant figures. ΟΙ ΑΣφ It vec ? R= ft Submit Request Answer Figure 1 of 1 Provide Feedback R A flow of 7200 ft3/min passes under the sluice gate. At depth yo = 6.5 ft...
A 12-in diameter pipe conveys fluid at 8 ft/s between two tanks. The friction factor f is 0.02. The pipe entrance and exits are both squared edged. The pipe also contains a fully-open gate valve. Determine what percent of the head loss is due to minor losses for the following three pipe lengths: (a) 4 ft, (b) 80 ft, (c) 1600 ft. Comment on whether minor losses are always “minor”.
Part A A flow of 7200 ft/min passes under the sluice gate. At depth yo = 6.5 ft the water is essentially at rest. (Figure 1) Determine the depth y2- Express your answer to three significant figures and include the appropriate units. μΑ ? Figure Y2 = Value Units < 1 of 1 Submit Request Answer 4 ft Part B Determine the depth yi just before the gate. Express your answer to three significant figures and include the appropriate units....
A flow of 7200 ft3/min passes under the sluice gate. At depth yo = 6.5 ft the water is essentially at rest. (Figure 1) Y2 = 1.71 ft Submit Previous Answers Correct Figure < 1 of 1 Part B 4 ft Determine the depth yi just before the gate. Express your answer to three significant figures and include the appropriate units. μΑ ? y = 4.93 yo Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Water...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
A pump that is 80% efficient pumps water from the lower tank to the upper tank at a flow rate of 0.01 m/s through 70 meters of 10-cm diameter pipe. In this system there are two regular, screwed 90 degree elbows and a fully open screwed angle valve. Assume the reservoir exits and entrances are sharp. The friction factor,f, of the pipe is 0.02. What horsepower pump is needed to achieve this flow rate? Use: Pwater = 998 kg/m2; Mwater...