For a hi-fi amplifier, a power gain of 30 is a decibel gain of ___ dB and a power gain of 50 is a decibel gain of ___dB.
For a hi-fi amplifier, a power gain of 30 is a decibel gain of ___ dB...
1) What is the gain at 100Hz for an amplifier that has a mid-band gain of 5000, a lower cutoff frequency of 10kHz, and a upper cutoff frequency of 200kHz 2)Calculate the decibel power gain for an Ap= 50? 3)If the decibel voltage gain of an amplifier is 60dB, what is the voltage gain (Av)? 4)If the decibel power gain of an amplifier is 20dB, what is the power gain (AP)? 5)For a two stage amplifier with AV1(DB) equal to...
1. If the voltage gain is 2000, the decibel voltage gain is a. 40 dB c. 66 dB b. 46 dB d. 86 dB 2. The input power to a device is 10.000 W. The output power is 500 W. The power gain (GdB) in decibels is a. -13 dB b. -26 dB c. 56 dB d. 18 dB 3. Which of the following is an advantage of using dB representations of gain values? (a) Positive and negative dB values...
An amplifier is specified by manufacturers to have a power gain of 45 dB when used with a 50 Ohm load. The input impedance is 1000 Ohm. If the input voltage is 0.1 V_RMs- what voltage appears across the load?
An amplifier is set to a gain of 7.5 dB. If 7.00×10-6 W of electrical power is applied to the input, how much power will be delivered at the output?
1. A high power amplifier is rated as having a gain of 36 dB. It receives an input power of 10 mW. What is the output power? 2. An electrical circuit has voltage attenuation of -3dB. Calculate Vout /Vin
4. Refer to the following amplifier assuming β-150 for Q1 an d Q2, and β-50 for Q3. (a) Find the total voltage gain in dB (20 points) (b) Find the total power gain dB (20 points) (c) Find the power efficiency (20 points) +15V Ry Ri Rc 0.22 μF ei 2, 1.0μF 47 Ω 500 mVppn 15 k2 Res 100μF 16Ω 2 W 1.0 kHz Ca RE: 160 4. Refer to the following amplifier assuming β-150 for Q1 an d...
14.4 An amplifier with a bandwidth of 1 GHz has a gain of 15 dB and a noise tem perature of 250° K. If it is used as a preamplifier in a cascade, preceding a microwave amplifier of 20 dB gain and 5 dB noise figure, determine the over all noise temperature.
Problem 6: Gain Given the transfer function of an amplifier is j0.003 G(w) = 600 · (1+ j0.003w) Find the magnitude |G(w)| of the gain. The decibel gain G(dB), is defined as G(dB) = 20log10|G (@)| Find the gain in decibels at: a) w = 0, b) w = 103 c) w = 106 Make a rough plot of G(db) vs frequency.
Assuming an ideal op-amp, design an inverting amplifier with a gain of 26 dB having the largest possible R1 value under the constraint of having to use resistors no larger than 1 MΩ. If the input voltage source of this amplifier has an internal resistance r0 = 50 kΩ, how will this affect the gain? Design a solution that will eliminate the effect of the internal source resistance without having to change the values of R1 and R2.
Can you please provide solution? Thanks If the voltage gain triples, the decibel voltage gain increases O A factor of 2 O by 3 dB O by 6 dB O by 9 dB 0 2