Refer to the Figure 3. The core has a relative permeability of 5,000. The peak(maximum) flux...
3.20 points - Magnetic circuit: A two-legged ferromagnetic core with relative permeability of 1500 is shown in the figure with its dimensions. Find the following: 1. Self and mutual inductances of the two windings with 400 and 300 turns. 2. What current will produce flux density of 1T in the core, if the first (left) winding with 400 turns is energized and the second winding is left open. 3. The rms voltage across the first winding, assuming the energizing source...
Question 7 A magnetic core is shown in Figure 1. Relative permeability of the core is 14 = 2000. Total number of winding turns in the left winding is NL = 100 and in the right winding is Nr = 10. Assume that the core cross section is uniform and the combined length of all air-gaps is much smaller than the dimensions of the core cross-section. Calculate the following: a) The magnetomotive force in the core if i = 2...
15 marks] B. A toroidal core with a mean diameter of 200 mm and a cross-sectional area of 800 mm has an air gap of length 1.1 mm cut in it Fringing and leakage of flux around the air gap may be neglected (i) Determine the current required in a coil of 1100 turns to produce a flux density of 1 T The relative permeability , of the core material (iron) may be assumed to be 3000 for this level...
A single phase transformer core, for use in a 50Hz electrical network, has the following magnetic characteristic Flux Density B Magnetic Field Strength H Total Core Loss 0.8 1.28 1.68 2.09297RMS Ampere-Turns/cm 1.23 1.85 2.2 2.73 Watts/k 1.0 1.1 1.2 Tesla The core has a cross-sectional area of 175cm2, the mean magnetic path length is 160cm and the density of the core material is 7.5gm/cm3. (a) If a no-load voltage ratio of 6600/231 is required, choose a suitable number of...
A laminated magnetic core is operating at 50 Hz with a peak flux density of 1 T. At this flux density, the core has an iron loss of 3 W. (a) The peak flux density is increased to 1.5 T. Estimate the new core loss. (b) The operating frequency is increased to 400 Hz with the original peak flux density of 1T. Estimate the new iron loss assuming that (i) the core only has hysteresis loss and has no eddy-current...
Chapter 2 Question A toroidal core of relative permeability 1000 has a mean diameter of 300 mm and a cross sectional area of 6 cm". The core is wound with 1000 turns. If a dc current establishes a flux in the core of 6 x 10-4 Webers, determine: (a) (1) the magnetic flux density. (ii) the inductance. (iii) the magnetic intensity (H). (iv) the stored energy.
Problem 1: A four pole, 60Hz, 3-d synchronous generator has a rotor radius of 15 cm, a rotor length of 2.7m, and an air gap length of 2 mm. The rotor field winding consists of 1000 turns with a winding factor of 0.962. The Δ connected armature winding has 25 series turns per phase with a winding factor of 0.935. The generator is designed to achieve rated open-circuit voltage at a peak air-gap flux density of 1.25 T (a) At...
Consider the core given in Fig.1. Relative permeability of the core material is 2000. a) What should be the coil current to achive a flux density of 2T when x-0. State your assumptions in the calculations b) Current in the coil is kept constant at the value found in part (a) as the armature moves to x-2 mm. What is the flux density when x-2 mm? alculate the energy stored in the magnetic circuit when x-0 and current in part...
Consider the core given in Fig.1. Relative permeability of the core material is 2000. a) What should be the coil current to achive a flux density of 2T when x-0. State your assumptions in the calculations b) Current in the coil is kept constant at the value found in part (a) as the armature moves to x-2 mm. What is the flux density when x-2 mm? alculate the energy stored in the magnetic circuit when x-0 and current in part...
EO Vuy vvvvvvvv NTurns 93 The relative permeability of the core material is 3500, and the average length of the core is 52cm as the cross- section of the core is 64cm2. The core is uniform of cross-section (all limbs have the same cross-section). There are 80 turns on the coil. Answer the following questions, 1) The reluctance of the core (AT/Wb) 2) Find the flux density (T) of the core if the current į in the coil is 0.75...