The oil in an engine is cooled by air in a cross-ow heat exchanger where both...
The oil in an engine is cooled by air in a cross-ow heat exchanger where both uids are unmixed. Atmospheric air enters at 30C and 0.53kg/s. Oil at 0.026kg/s enters at 75C and ows through a tube of 10-mm diameter. Assuming fully developed ow and constant wall heat ux, estimate the oil-side heat transfer coefcient. If the overall convection coefcient is 53W/m2K and the total heat transfer area is 1m 2, determine the effectiveness. What is the exit temperature of the oil?
Homework Answers
Add Answer to:
The oil in an engine is cooled by air in a cross-ow heat
exchanger where both...
4. A Cross-Flow Air-to-Water Heat Exchanger with an effectiveness of 0.58 is used to heat water, ...
4. A Cross-Flow Air-to-Water Heat Exchanger with an effectiveness of 0.58 is used to heat water, entering at 20°C at a rate of 4 kg/s, using hot air, entering at 127oC at a rate of 10 kg/s. The Overall Heat Transfer Coefficient for the Heat exchanger is 275 W/m'K. Assuming both fluids are unmixed, determine; (i) The Heat Capacity rates for both the air and the water (ii) The heat transfer surface area. ii) The exit temperature of the water...
please do 11.33 11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat...
please do 11.33
11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 80°C at a rate of 3 kg/s. The exhaust gases, hav- ing thermophysical properties similar to air, enter and exit the exchanger at 225 and 100°C, respectively. If the overall heat transfer coefficient is 200 W/m2.K, estimate the required surface area. 11.33 Consider the fluid conditions and overall heat transfer coefficient of Problem 11.32 for a concentric tube heat...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water,...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water, which has a flow rate of 0.045 kg/s, enters the radiator at 400 K and is to leave at 330 K. The water is cooled by air that enters at 0.75 kg/s and 300 K. If the overall heat transfer coefficient is 220 W/m2.K, what is the required heat transfer surface area, in mº? Assume that T =320 K when evaluating the properties of...
Oil of unknown properties is heated in a shell-and-tube heat exchanger with one shell pass and...
Oil of unknown properties is heated in a shell-and-tube heat exchanger with one shell pass and 20 tube passes. The oil flows through the shell, and hot water flows inside the single copper tube that has an inner diameter of 20 mm, a wall thickness of 2 mm, and a length of 3 m per pass. The water enters at 360 K at a mass flow rate of 0.2 kg/s and leaves at 300 K. The inlet and outlet temperatures...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water,...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water, which has a flow rate of 0.055 kg/s, enters the radiator at 400 K and is to leave at 330 K. The water is cooled by air that enters at 0.75 kg/s and 300 K. If the overall heat transfer coefficient is 180 W/m2.K, what is the required heat transfer surface area, in m?? Assume that TC,0 = 320K when evaluating the properties of...
A concentric tube heat exchanger for cooling lubricating oil consists of a thin-walled inner tube of...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Problem (25 Points - Chapter 11) A concentre tube heat exchanger for cooling lubricating oil is...
Problem (25 Points - Chapter 11) A concentre tube heat exchanger for cooling lubricating oil is comprised of a thin-walled me tube of 25-mm diameter carrying water and an our tube of 45mm diameter coming the The heat exchanger operates in counterflow with an overall heat transfer coefficient of W K and the average property as given in the table below. If the outlet temperature of the oil is 60°C, determine the following (a) total heat transfer rate, (b) outlet...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters of 10.2mm and 12.5mm and has to be cooled to 136°C. The tubes are made of steel of thermal conductivity k-40 W/m.K. Air at 10°c enters the exchanger (unfinned) with a volumetric flow rate of 1.0 m3/s. The convective heat transfer coefficient...
Hot air enters a heat exchanger at 350°C and exits at (149°C. The heat extracted is...
Hot air enters a heat exchanger at 350°C and exits at (149°C. The heat extracted is used to boil (0.263) kg/s of 100°C water (from saturated liquid to saturated steam). The heat exchanger is a single-shell shell-and-tube heat exchanger with two tube passes. The overall heat transfer coefficient for the hot side is 240 W/(m2°C). Assume a constant specific heat for air of Cp = 1.005 kJ/(kgC). The pressure of the hot air and the boiling water is P =...
10-58) An air preheater for a power plant consists of a cross-flow heat exchanger with hot...
10-58) An air preheater for a power plant consists of a cross-flow heat exchanger with hot exhaust gases used to heat incoming air at I atm and 300 K. The gases enter at 375°C with a flow rate of 5 kg/s. The airflow rate is 5.0 kg/s, and the heat exchanger has A = 110 m2 and U = 50 W/m2 oC. Calculate the heat-transfer rate and exit temperatures for two cases, both fluids unmixed and one fluid mixed. Assume...
4. A Cross-Flow Air-to-Water Heat Exchanger with an effectiveness of 0.58 is used to heat water, entering at 20°C at a rate of 4 kg/s, using hot air, entering at 127oC at a rate of 10 kg/s. The Overall Heat Transfer Coefficient for the Heat exchanger is 275 W/m'K. Assuming both fluids are unmixed, determine; (i) The Heat Capacity rates for both the air and the water (ii) The heat transfer surface area. ii) The exit temperature of the water...
please do 11.33
11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 80°C at a rate of 3 kg/s. The exhaust gases, hav- ing thermophysical properties similar to air, enter and exit the exchanger at 225 and 100°C, respectively. If the overall heat transfer coefficient is 200 W/m2.K, estimate the required surface area. 11.33 Consider the fluid conditions and overall heat transfer coefficient of Problem 11.32 for a concentric tube heat...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water, which has a flow rate of 0.045 kg/s, enters the radiator at 400 K and is to leave at 330 K. The water is cooled by air that enters at 0.75 kg/s and 300 K. If the overall heat transfer coefficient is 220 W/m2.K, what is the required heat transfer surface area, in mº? Assume that T =320 K when evaluating the properties of...
Oil of unknown properties is heated in a shell-and-tube heat exchanger with one shell pass and 20 tube passes. The oil flows through the shell, and hot water flows inside the single copper tube that has an inner diameter of 20 mm, a wall thickness of 2 mm, and a length of 3 m per pass. The water enters at 360 K at a mass flow rate of 0.2 kg/s and leaves at 300 K. The inlet and outlet temperatures...
An automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. Water, which has a flow rate of 0.055 kg/s, enters the radiator at 400 K and is to leave at 330 K. The water is cooled by air that enters at 0.75 kg/s and 300 K. If the overall heat transfer coefficient is 180 W/m2.K, what is the required heat transfer surface area, in m?? Assume that TC,0 = 320K when evaluating the properties of...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Problem (25 Points - Chapter 11) A concentre tube heat exchanger for cooling lubricating oil is comprised of a thin-walled me tube of 25-mm diameter carrying water and an our tube of 45mm diameter coming the The heat exchanger operates in counterflow with an overall heat transfer coefficient of W K and the average property as given in the table below. If the outlet temperature of the oil is 60°C, determine the following (a) total heat transfer rate, (b) outlet...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters of 10.2mm and 12.5mm and has to be cooled to 136°C. The tubes are made of steel of thermal conductivity k-40 W/m.K. Air at 10°c enters the exchanger (unfinned) with a volumetric flow rate of 1.0 m3/s. The convective heat transfer coefficient...
Hot air enters a heat exchanger at 350°C and exits at (149°C. The heat extracted is used to boil (0.263) kg/s of 100°C water (from saturated liquid to saturated steam). The heat exchanger is a single-shell shell-and-tube heat exchanger with two tube passes. The overall heat transfer coefficient for the hot side is 240 W/(m2°C). Assume a constant specific heat for air of Cp = 1.005 kJ/(kgC). The pressure of the hot air and the boiling water is P =...
10-58) An air preheater for a power plant consists of a cross-flow heat exchanger with hot exhaust gases used to heat incoming air at I atm and 300 K. The gases enter at 375°C with a flow rate of 5 kg/s. The airflow rate is 5.0 kg/s, and the heat exchanger has A = 110 m2 and U = 50 W/m2 oC. Calculate the heat-transfer rate and exit temperatures for two cases, both fluids unmixed and one fluid mixed. Assume...
Most questions answered within 3 hours.
-
Trace the following recursive methods:
a) isPal with the string “abccda”
b) isAnBn with the string...
asked 31 minutes ago -
1. Which of the following is false about photosynthesis?
A. ATP is the molecule used to...
asked 1 hour ago -
A simple random sample of size n=64 is obtained from a
population with a mean of...
asked 2 hours ago -
(2 dimensions, 1 object, 2 accelerations)
1) A projectile is thrown with a wind. The wind...
asked 3 hours ago -
Brian makes $34,100 per year. How much can Brian expect to
contribute to FICA taxes in...
asked 3 hours ago -
To buy a new house you must borrow $155,000. To do this you take
out a...
asked 4 hours ago -
Spacely Sprockets is evaluating the construction of a new plant
on land the company purchased for...
asked 4 hours ago -
1. Consider a linear regression model of y on K regressors and
an intercept.
(i) Describe...
asked 4 hours ago -
Enter a balanced equation for the reaction between hydrochloric
acid and sodium sulfite.
Express your answer...
asked 5 hours ago -
Give a regular expression describing the language
{x | x ∈ Σ* and x does not...
asked 5 hours ago -
Masses of 1.0 kg, 2.0 kg, and 3.0 kg are each separately subject
to a net...
asked 5 hours ago -
The mode of philosophical argumentation and thought. How do
philosophers think and write? What is important...
asked 5 hours ago