Brass bushings have a length of 10 cm, inside diameter of 12 cm, and wall thickness...
Brass bushings have a length of 10 cm, inside diameter of 12 cm, and wall thickness of 4 cm; a density of brass is 8.62 gcm-3. A manufacturer plans to use a centrifugal casting method for making the bushings.
a. Name an appropriate centrifugal casting process for making the bushings.
b. Determine the rotational speed that obtains a G-factor (GF) of 70.
c. When operating at this speed, determine the centrifugal force per square meter (Pa) imposed by the molten metal on the inside wall of the mould.
Homework Answers
Request Answer!
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Add Answer to:
Brass bushings have a length of 10 cm, inside diameter of 12 cm,
and wall thickness...
Plz answer 3.3 and 3.4 Question 3 10 Marks During laboratory testing of a thin-wall pressure vessel, the cylinder diameter and thickness were at 10 different locations: the resulting data were as...
Plz answer 3.3 and 3.4
Question 3 10 Marks During laboratory testing of a thin-wall pressure vessel, the cylinder diameter and thickness were at 10 different locations: the resulting data were as follows If the pressure inside the vessel is measured to be P - 1 mPa (mega Pascal) with an estimated uncertainty of up-+ 6 kPa (kilo Pascal, for 95% confidence interval, the tangential or hoop stress in the vessel is given by ơe-- 3.1 Compute the uncertainty in...
The cylindrical pressure vessel shown in the figure has an inside diameter of 980 mm and a wall thickness of 12 mm. The cylinder is made of an aluminum alloy that has an elastic modulus of E = 72 GPa...
The cylindrical pressure vessel shown in the figure has an
inside diameter of 980 mm and a wall thickness of 12 mm. The
cylinder is made of an aluminum alloy that has an elastic modulus
of E = 72 GPa and a shear modulus of G = 27.5
GPa. Two strain gages are mounted on the exterior surface of the
cylinder at right angles to each other. The angle θ is 21°. If the
pressure in the vessel is 1.86...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Plz answer 3.3 and 3.4
Question 3 10 Marks During laboratory testing of a thin-wall pressure vessel, the cylinder diameter and thickness were at 10 different locations: the resulting data were as follows If the pressure inside the vessel is measured to be P - 1 mPa (mega Pascal) with an estimated uncertainty of up-+ 6 kPa (kilo Pascal, for 95% confidence interval, the tangential or hoop stress in the vessel is given by ơe-- 3.1 Compute the uncertainty in...
The cylindrical pressure vessel shown in the figure has an
inside diameter of 980 mm and a wall thickness of 12 mm. The
cylinder is made of an aluminum alloy that has an elastic modulus
of E = 72 GPa and a shear modulus of G = 27.5
GPa. Two strain gages are mounted on the exterior surface of the
cylinder at right angles to each other. The angle θ is 21°. If the
pressure in the vessel is 1.86...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
convert grams into vloume with the density of water being at
.997514 g/cm^3 at 23.1 Celsuis...
asked 4 minutes ago -
Foreman company obtained a $20,000, 6% loan on May 1, 2018.
Principal and interest will be...
asked 8 minutes ago -
5. Problem 11.05 (Discounted Payback)
eBook
Project L costs $60,000, its expected cash inflows are $14,000
per...
asked 36 minutes ago -
1. Which of the following is true about politics and health
organizations?
A. Health organizations are...
asked 1 hour ago -
A space vehicle is coasting at a constant velocity of 18.1 m/s
in the +y direction...
asked 2 hours ago -
5) Use the following balanced equation to answer questions
(a)-(i).
3 Cu(s) + 8 HNO3(aq) →...
asked 1 hour ago -
A three-year maturity bond with a 12% annual coupon rate is
currently traded at par $1000...
asked 1 hour ago -
1.
What is the minimum volume to use in the Spec 20 cuvette in order
to...
asked 2 hours ago -
A builder wants to install wall-to-wall carpeting in a living
room of length 8.87 m and...
asked 2 hours ago -
Organizational change can produce anxiety in those affected by
the change. In what ways can change...
asked 2 hours ago -
Ozone in the atmosphere may react with nitric oxide.
From the following data, calculate the DG...
asked 2 hours ago -
Steven Long, a bond analyst, is analyzing a convertible bond.
The characteristics of the bond are...
asked 2 hours ago