Question 3 (25 pts): 1. The following PV diagram shows an adiabatic process. How m though...
D Question 1 1 pts An adiabatic heat exchanger is used to heat cold water at 12 °C entering at a rate of 4 kg/s by hot water entering at 95°C at rate of 2.5 kg/s. The specific heat of water is C_w 4.18 kJ/kg- C. If the exit temperature of hot water is 50 °C, the exit temperature of cold water is O 50 °C 90 °C 95 °C 57 °C 40 °C
Question 9 2 pts Ch 15:33 How many Joules of heat are required to raise the temperature of 0.7 kg of water by 22 °C? HINT: Use the equation AT Q. The specific heat capacity of water J is c = 4190 сть kg C
Question 17 3 pts A 771.0-kg copper bar is put into a smelter for melting. The initial temperature of the copper is 300.0 K. How much heat must the smelter produce to completely melt the copper bar? The specific heat for copper is 386 J/kg · K, the heat of fusion for copper is 205,000 J/kg, and its melting point is 1357 K. O 3.15 x 1011kg 4.73 x 105 kJ 3.15 x 108 kJ 5.62× 105 kJ Question 18...
Question 13 (1 point) How much heat (in MJ) does it take to completely convert 0.80 kg of ice initially at a temperature of -15°C to steam (water vapor) at a final temperature of 130°C? Specific heats (in J/kg.K): ice (2100), water (4190), steam (2000) Latent heats (in J/kg): fusion (3.34 x 105), vaporization (2.256 X 106) 1.0 2.0 1.5 2.5 0.5 3.0
4. (25 pts) Water is flowing inside a thin wall, smooth pipe of diameter 0.05 m at a mass flowrate of 0.3 kg/s. The water enters the pipe at a mean temperature Tm,i= 80 °C and exits at Tm,o= 80 °C while the pipe surface temperature is maintained at Ts= 20 °C along its entire length. a. Is the flow turbulent or laminar? b. Calculate the average convection heat transfer coefficient inside the tube. c. Calculate the length of the...
3 please
Question 3 10 pts 0.2000kg of molten copper at the melting point 1083°C, is placed into a 375.2g aluminum calorimeter cup filled with a quantity of ice both initially at 0.000°C. If the final temperature of the system is 91.50°C, what is the mass of the ice in kilograms in the calorimeter cup initially? The specific heat for water is 4186J/kg°C, for copper is 387J/kg°C, and for aluminum is 900 J/kg°C. The latent heat of fusion for water...
At 1 atm, how much energy is required to heat 0.0550 kg of ice at -22.0 °C to steam at 129.0 °C? STRATEGY 1. Calculate the energy needed for each temperature change or phase change individually. A. The energy needed to heat 0.0550 kg of ice from -22.0 C to its melting point. B. The energy needed to melt 0.0550 kg of ice at its melting point C. The energy needed to heat 0.0550 kg of liquid water from the...
(25 pts) A well-insulated and well-sealed 2-m x 3-m x 4-m room is initially at Tal = 22 °C and p = 100 kPa. A mass of mw = 20 kg of liquid water at Tw./ = 80 °C is brought into the room and the system is allowed to reach equilibrium conditions (state 2). 2m x 3m x 4m ROOM 22°C 100 kPa Specific heat values for the air and water may be taken as Cp,air = 1.005 kJ/kg-K;...
Question 1 1 pts A 50 g block of aluminum is dropped into a beaker with 300 g of water. The initial temperature of the block is 200 °C, and the water is at room temperature (23 °C). (The specific heat of water and aluminum are 4186 J/kg K and 900 J/kg K, respectively.) The final temperature of the aluminum and the water is 29.1 °C, how much energy was transferred to the water? 36544 7660J O 1647J 7.66x 106...
pts per question) 1. A 2 m piston cylinder device contains nitroen gas at 200 kPa and 350K. Now heat is transferred to the nitrogen in the tank and the pressure of nitrogen rises to 900 kPa and volume is maintained at same. The boundary work done during this process is (a) 1080 kJ (b) 840 k (c)240 k 2. A heat engine receives heat from a source at 727°C and rejiects the waste heat to a sink at 27°C,...