1. a. Build a second order low pass filter with -3dB frequency at 5kHz. Given L...
Determine the transfer function for a 2nd order Chebyshev low pass filter with 3dB frequency of 100krad/sec, a maximum gain of OdB, and a passband ripple of 1dB. (40 points) (a) (b) A bandpass filter is made by cascading the filter described in part (a) with a 2nd order Chebyshev high pass filter with 3dB frequency of 1krad/sec, a maximum gain of OdB and passband ripple of 2dB. Determine the midband gain of the filter. (30 points) A Chebyshev bandpass...
A) Design a low - pass filter with a -3dB frequency equal to the four digits of your birth month and day (in Hz). Choose a reasonable value for your capacitor or inductor. 4. B) Give an example that you prefer a 1X over a 10X probe to measure the voltage of acircuiit hode. C)What is the value of a precision resistor with the code 4321F?
Design a second order IIR Butterworth low pass digital filter with a cutoff frequency of 500 Hz and a sampling frequency of 10,000 Hz using bilinear transformation then find the following: The output (response) due to the following inputs: Sinusoidal signal with a frequency of 100Hz. Sinusoidal signal with a frequency of 500Hz. Sinusoidal signal with a frequency of 2000Hz. Repeat (a) above for a 6thorder Butterworth filter
10 Design a low pass filter using a resistor R and a capacitor C of 0.2uF. Sketch the circuit diagram, mark thoe output voltage Vo, calculate the resistance value for R if 3dB frequency is 2500 Hz, and write out the voltage gain vs ω (for both magnitude and phase). Repeat the design if R is given as 30 Ohm and C is unknown.
Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter with cut-off frequency of 1 kHz & gain 20dB. Design a first order active low-pass filter with cut-off frequency of 1 kHz & gain 20dB. Plot the magnitude and phase responses of the active high-pass and low-pass filters you have designed using PSpice (Use UA741 Op amp and ±12V dual supply). Connect your active low-pass and high-pass filters as shown in Fig. 1-b. Assume...
Design a second-order Butterworth low-pass filter to satisfy the specifications a. The dc gain is unity (zero dB); b. The gain is no smaller than -1 dB for frequencies between 0 and 2,000 Hz; and c. The gain is no larger than -40 dB for frequencies larger than 40 kHz. Determine a circuit realization as a series RLC low-pass filter. Pick reasonable values of R, L, and C. Design a second-order Butterworth low-pass filter to satisfy the specifications a. The...
Draw the circuit diagram and derive the frequency transfer function for the first-order passive RL low-pass filter (voltages as input and output). If this filter has a time constant of 2s and the input voltage signal is cos(πt) + sin(3πt) in the time domain, find the output signal in the time domain.
A single stage band pass filter was created. The low pass filtering stage consists of a 5kohm resistor and a 0.3nF capacitor. The high pass filtering stage consists of a 10nF capacitor and a 1,6kOhm resistor. a. Determine an equation and calculate the frequency at which the output voltage is 10% that of the input voltage. b. Determine an equation and calculate the frequency at which the power transfer is -10dB.
Learning Goal: To analyze and design a passive, first-order low- pass filter using a series RL circuit. The analysis and design will be repeated for a series RC circuit. An electrocardiogram needs to detect periodic signals of approximately 1 Hz (since the resting heart rate of a healthy adult is between 55 and 70 beats per minute). The instrument operates in an electrical environment that is very noisy with a frequency of 60 Hz. It is desirable to have a...
Learning Goal: To analyze and design a passive, first-order low-pass filter using a series RL circuit. The analysis and design will be repeated for a series RC circuit. An electrocardiogram needs to detect periodic signals of approximately 1 Hz (since the resting heart rate of a healthy adult is between 55 and 70 beats per minute). The instrument operates in an electrical environment that is very noisy with a frequency of 60 Hz. It is desirable to have a low-pass...