Please answer every part 1) Six Transistor CMOS Logic Circuit, Z-output; A, B, C are the...
Please answer every part 1) Six Transistor CMOS Logic Circuit, Z-output; A, B, C are the inputs. 15 pts The three P-devices are connected as follows: Q2S-5V; Q2D-Q4S Q6S; Q4D-Q6D-Z. The three N-devices are connected as follows: QiS-GND Q3D-Q5S Q3S GNDQID-Q5D-Z The three inputs are connected as follows: A-QIG-Q2G; B-Q3G-Q4G; C Q5G Q6G. a) Draw the CMOS circuit. 3 pts b) Draw the function table for the three inputs, the six transistors and the output, Ζ. Use 0 for an...
Design and implement a combinational circuit with four inputs w,x, y and z and four outputs A, B ,C and D using CMOS transistors. When the binary input is 0, 1, 2,3,4,5,6 or 7 the binary output is five greater than the input. When the binary input is 8,,10,11,12,13,14 or 15 the binary output is seven less than the input. for question (a) find the troth table for the inputs (ABCD) then implement using K-map to find the equations to...
The layout of a CMOS complex logic circuit is given in the Figure 1 4. Draw the corresponding circuit diagram; and (10 Marks) a. b. Calculate the (W) of all the nMOS and PMOS transistors for simultaneous switching (W/), 15 for all of all the inputs, assuming that (Wh),-20 for all pMOS transistors and (w/L), = 15 for all (WL 20 for all pMOS transistors and (10 Marks) nMOS transistors VDD n well metal poly silicon n+ diffussion OUT Contact...
solve both 2.10 Find the transistor schematic for the CMOS logic circuit realized by the layout shown in Fig. P2.10. Give the widths of all transistors. AssumeL = 21, where A = 0.4 um. In tabular form, give the area and perimeter of each junction that is not connected to VDD or to ground. VDD Polysilicon 8A n well -p diffusion Active region Out 6/ n diffusion Metal Gnd A Fig. P2.10 D 17.33 The circuit of Fig. P17.33 consists...
1. a. Design and implement a combinational circuit with three inputs w, x, and y and three outputs A, B and C using CMOS transistors. When the binary input is 0, 1, 2 or 3 the binary output is three greater than the input. When the binary input is 4, 5, 6 or 7 the binary output is three less than the input. b. from the part (a) , Draw the mask layout with Ln = Lp= 0.6 μm, Wn=...
a. Design and implement a combinational circuit with four inputs w,x, y and z and four outputs A, B,C and D using CMOS transistors. When the binary input is 0, 1, 2,3, 4, 5, 6 or 7 the binary output is three greater than the input. When the binary input is 8,10,11,12,13,14 or 15 the binary output is five less than the input. b. Draw the mask layout with Ln Lp 0.6 um, Wn- 4.8 um and Wp- 9.6 um...
a. Design and implement a combinational circuit with four inputs w,x, y and z and four outputs A, B,C and D using CMOS transistors. When the binary input is 0, 1, 2,3, 4, 5, 6 or 7 the binary output is three greater than the input. When the binary input is 8,10,11,12,13,14 or 15 the binary output is five less than the input. b. Draw the mask layout with Ln Lp 0.6 um, Wn- 4.8 um and Wp- 9.6 um...
digital logic & design questions 1. Find the output function of this circuit, X. B C 2. Use k-map to simplify the function X to its minimum Sum Of Product (SOP Draw the logic circuit of the simplified function X using the 74LS54 And Or Invert (AOD chip. 3. 74LSS4 Problem#4: The logic circuit in (a) is implemented using a 7400 IC chip. The conections on is not working properly! the problem is in the IC connections or in the...
1. Consider the circuit below a. What is the logic function implemented by the CMOS transistor network? Size the NMOS and PMOS devices so that the output resistance is the same as that of an inverter with an NMOS WIL 4 and PMOS W/L 8 b. What are the input patterns that give the worst case tpHL and tpLH. State clearly what are the initial input patterns and which input(s) has to make a transition in order to achieve this...
2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you can get the logic, the less work you will have). You must draw the circuit with transistors In Out DUIi 0111 011 0011 010 0001 001 2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you...