2. What is the maximum current that can be put across a 0.1 W, 50 k?...
4. For each of the following circuits, A, B, C, and D, will you measure a current across the resistor? Why or why not? Assume the power supply voltage is less than te breakdown voltage for the diodes
5. A light emitting diode (LED) is a diode that lights up when a current flows across it. The symbol for an LED is shown below (sometimes wiggly arrows are used to represent the light instead.) For this question we will assume we are working with LEDs that have a turn-on voltage of VoN-1V and a reverse breakdown voltage of VBR-8V a. You hook up a single LED to a power supply that can put out vol tage from -10...
15 Electrical Circuits Lab E: PARALLEL CIRCUITS Name wr w¡ฆ now discover how cument, voltage, and r cireuit. Set the power supply at 1.5 V for this lab, or use a single dry cell EXCEED ISV resistance eperate in any parallel 1.5 Do NOI Step 1: Set sp a circuit with a power supply set at 1.5 V and two resistors as shown in diagram A. The ammeser is positioned to measure the current entering Diagram A resistor one (Rj...
Pease answer questions 4 and 5! Thank you so much!
4. Connect the 2nd resistor in parallel with the 1st
resistor and connect that combination to the battery.
Measure
the following:
The
current passing through the R1, I1 = ___0.0058____ A
The
current passing through the R2, I2 = ___0.0031____ A
The
current supplied by the battery, I = ___0.0092____ A
Calculate I1 + I2 = ____________ A
Is the following statement true? I = I1 +...
Circuits The table beside circuit a below shows the current through each resistor, the voltage across each resistor, and the power dissipated as heat in each resistor. Find the similar correct value for circuits b, c, and d, and put your answers in the tables shown.
ANALYSIS Use your experimental results to analyze the circuit in terms of Kirchhoff net current fow into and out of each of the four nodes, and determine whetheC s Rules. Consider supported by your data. Determine the net voltage drop around at leaston Sign determine whether or not your data supports the loop rule. (Pay close attosed loops convention.) In adition, verify ir Ohm's law is satisfied for at least three resistors and for the total reji >Q12: Why do...
Name: ENGT 3050 Fundamentals of Electricity LAB EXERCISE #3 Series and Parallel Circuits Objectives: The objective of this exercise is to examine Kirchhoff's Voltage and Current Laws. Kirchhoff's Voltage Law (KVL) states, for a closed loop series path the algebraic sum of all the voltages around any closed loop in a circuit is equal to zero. Kirchhoff's Current Law (KCL) states, for a parallel path the total current entering a circuits junction is exactly equal to the total current leaving...
With the given information, what are the following
values?
Also, sorry for the picture quality. it was the best I could
do.
The voltage is 0.528 V(in volts) and the current is in
amperes. However, I think it needs to be converting to mA. So, I
believe the current is 0.1483 mA, 0.0925 mA, 0.00498 mA.
Parallel Circuit Voltage V Total current A Observed total Ω Theoretical Rotal 12 Do the observed results agree reasonably with the experimental value? 1....
ENGR 1181 Lab 3: Circuits Preparation Material Lab 3: Circuits Lab-Pre-lab Assignment Team Seat No. Name This is an individual assignment Solve the five problems below and hand it in at the beginning of the Circuits Lab. Show all your work Problem 1. Ohm's Law For the circuit below, calculate the value of the resistor R which would cause the current of 2.5 mA to flow in the circuit What voltage would you measure across the resistor? Show your calculations....
1. calculate node voltage V1 and V2
2. calculate the voltage drop across 10k resistor equal to the
difference between V2 and Vs2
3. Calculate mesh current i1,i2, i3
4. calculate the current through 2.7k resistor
5. does the current measured through 2.7k resistor equal to the
difference between the currents i2 and i3? show all
calculations
equired Itheory a Construct the circuit shown in Fig. 2 on your breadboard. 1 k 2 w V, 1k22 V, 10 k92 VS2...