Question (2): Use the finite element modeling to predict the temperature distribution and heat flow throngh...
THE FINITE VOLUME a composite wall is made of two materials (A with ka = 0.8 W / m-K and B with kb = 4 W / m-K), each with a thickness L = 10 mm. The surface of the wall A at x = 0 is perfectly insulated. A very thin heater is placed between the insulator and material A, giving a heat flow of 4500 W / m2. The wall surface at x = 2L is exposed to...
finite element method 2. Aluminum fins with rectangular profiles (5 mm wide and 1 mm thick) are used to remove heat from a surface whose temperature is 150°C. The temperature of ambient air is 20°C. The thermal conductivity of aluminium is 168 W/m.K. The natural convective coefficient associated with the surrounding air is 35 W/m2.K. The fins are 150 mm long and the heat loss from the tip of the fin may be neglected. (a) Determine the temperature distribution along...
PLEASE WRITE/PRINT CLEARLY AND SOLVE USING THE FINITE ELEMENT METHOD UNCLUDING MATRICIES 2. The flow rate at node 1 is 0.16 liter/s (0.16 *10-2 m/s). The pressure at node 4 is 0 Pa (g). For the given conditions, the flow is laminar throughout the system. Using hand calculation determine i. The pressure in each node. ii. Flow in each element iii. Verify your results (25 + 10 + 5 = 40) (1) L=10 m D=20 mm u = 8 x...
QUESTION 4 For the convection heat transfer problem shown in the following figure, (a) write the finite element model related to cach of the four rectangular elements, (b) write the finite clement algebraic equation for the unknown nodal temperatures at Node 5, Assume that the thermal conductivity of the material is k-5 W(m.C), the convection heat transfer coefficient on the left surface is -28 W/(m C), and the internal heat generation is zero. (25 pts) Use the following sense and...
The heat that is conducted through a body must frequently be removed by other heat transfer processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature T. The conductivity of the aluminum fin (k) and coefficient of heat convection of...
PLEASE WRITE/PRINT CLEARLY PLEASE SOLVE USING THE FINITE ELEMENT METHOD WHICH INCLUDES THE MATRIXES 2. The flow rate at node 1 is 0.16 liter/s (0.16 *10 m/s). The pressure at node 4 is 0 Pa (g). For the given conditions, the flow is laminar throughout the system. Using hand calculation determine i. The pressure in each node. ii. Flow in each element iii. Verify your results (25 + 10 + 5 = 40) (1) L= 10 m D-20 mm [2]...
finite element method The equation for the heat diffusion of a one-dimensional system widh heat generation in a Cartesian coordinate system is 4. d'T dx2 The rate of thermal energy generation q represents the convessice of enery os electrical, chemical, nuclear, or electromagnetic forms to thermal energy witin the volume of a given system. Derive the contribution of á to the load matrix. Consider a strip of heating elements embedded within the rear glass of a car peoducing a uniform...
finite element method Expert Q&A Done Finite element method QUESTION 2 (20 Marks) Concept question of a horeoital steel beam ) State clearly the element types of (c) What are direct sess and combined sress? Desorbe in words how (s marks 25 KN 1.8 m 10 mm 100 mm 1.0 m ←1.5 m 3.0 m Figure 2 Diagram for Question 2 Expert Q&A Done Finite element method QUESTION 2 (20 Marks) Concept question of a horeoital steel beam ) State...
20) Me Steady-state temperature distribution in the s figure. The heat flow is one-dimensional. ibution in the sandwich of three materials (A, B, and C) is shown in the aterial B has volumetric heat generation à = 64,000 W/m. Material A has thermal conductivity of 10 W/ m K . Determine: a) The heat flux at the left side: b) The heat flux at the right side: c) The thermal conductivity of Material C: : - W/m2 W/m2 _W/mK T[deg.]...
1) 2) 3) PROJECT #1 (2.5 Marks): The heat that is conducted through a body must frequently be removed by other heat transter processes. For example, the heat generated in an electronic device must be dissipated to the surroundings through convection by means of fins. Consider the one-dimensional aluminum fin (thickness t 3.0 mm, width Z 20 cm, length L) shown in Figure 1, that is exposed to a surrounding fluid at a temperature 1. The conductivity of the aluminum...