3.130 points) The volume flow rate through a pump system operating between two harge bodies of water of density p, is V. The head loss through the pipe/turbime network is a. (15 points) Derive and expression for the power provided by the pump, W, in terms of the known variables only. The "know variables" are p, V, H, D and g. b. (5 points) Given V 100 m/s, g-9.81 m/s?, D-1 m and H-20 m. What is the average velocity...
Consider the nozzle given below. The nozzle exit has an area 0.0011 m^2 and a pressure of 0 kPa (gauge). Given the mass flow and cross sectional area of the nozzle entrance, what is the pressure at the nozzle entrance (P1) ? Give the answer in kPa gauge, but do not enter the units in the answer box. The fluid is water with a density of 1000 kg/m^3. Ignore work and friction. The external force is still unknown. mass flow...
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter of intake pipe = 160 mm; entrance losses = one velocity head in suction pipe; required NPSH = 42 kPa; water temperature = 30°C N D1, D2 : inlet and outlet diameters of impeller (rotor) b : impeller width 0,6 : inlet and outlet impeller vane angles (degrees) : speed of rotation of impeller (and its driver) in rpm V, V :tangential and radial...
Q2 Water flows at a rate of 0.08 m''min through a flanged tap with a partially closed gate valve spigot (Fig. Q2). The inner diameter of the pipe at the inlet and outlet is 2 cm and 1.5 cm respectively, and the gauge pressure of the water at inlet is measured to be 90 kPa. The pressure at outlet from the tap is atmospheric. The total mass of the tap assembly plus the water within it is 5.8 kg. (a)...
Problem The relation between pressure drop and flow rate of laminar flows in a pipe is given by l bar 50 m 20° 128u dz PS Flow rate Q is the product of the average velocity and the cross-sectional area of the pipe What is the pressure needed to drive a viscous oil flow upslope through a 12 cm diameter pipe? The length of the pipe is 50 meters. The slope is 20°. At the end of the pipe, the...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at an elevation 10 m above the reservoir surface. The mass flow rate is 40 kg/s and the volumetric flow rate is 0.040 m3/s. The large diameter inlet pipe total length is 50 m. The pump effidency is 65%. The longer smaller diameter pipe leaving the pump is 200 m in total length. The pipes have different diameters as indicated below. The...
40 N"s/m2 and ?-1000 kg/m3 is flowing through a circular pipe umetric flow rate (Q) of the oil is 1*10 m'/s, determine: 1) (2096) Oil with viscosity of with diameter D 0 0.1 m. If the volu a. b. If the flow is laminar or turbulent Th e pressure drop over a 20 m length of p ipe in kPa
Water (density 998 kg/m', absolute viscosity 1.12x10 Ns/m2) is pumped from a lake into a reservoir at a rate of 0.7 m/s. The water flows through a re-entrant opening, a valve, and a sharp-edged exit, which have loss coefficients of 0.8, 10, and 1, respectively. The pipe has an absolute roughness of 1x104m and di of 0.30 m. The pump efficiency is 65%. A) Is the flow in the pipe laminar or turbulent? (2 points) B) What is the power...
PROBLEM 1 (50 points) Pa= 100 kPa D=0.1 m Po=500 kPa To-300 K Convergent nozzle alone Nozzle Exit Pa 100 kPa f- 0.005 D= 0.1 m Po=500 kPa To-300 K Convergent nozzle + pipe L= 10 m Nozzle Exit Pipe Exit A convergent nozzle of diameter D = 0.1 m is connected to a reservoir with pressure po=500 kPa The convergent nozzle supplies flow to a pipe of equal diameter with length L = 10 m and friction factor f...