3 out of 3 attempts The 5-mm-diameter cable B C is made of a material with...
The 4-mm-diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 5 mm, find the maximum load P that can be applied as shown. В 2.5 m P 3.5 m с -4.0 m
Required information The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 200 MPa and that the elongation of the cable must not exceed 7 mm. Ifa - 3 m and b 4 m, find the allowable load P that can be applied as shown
5. (10pts) the 4-mm-diameter cable BC is made of a steel with E = 200 GPa as shown in Fig. 2. Knowing that the maximum stress in the cable must not exceed 190MPa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can be applied. -BQ 2.5 m P 3.5 m 14.0m Fig. 2
A 1.5-m-long aluminum rod must not stretch more than 1 mm and the normal stress must not exceed 40 MPa when the rod is subjected to a 3.0-kN axial load. Knowing that E= 70 GPa, determine the required diameter of the rod. The required diameter of the rod is mm.
the hollow tube down has an outside diameter of 45 mm and an inside diameter of 40 mm. the tube is made of an aluminum alloy with a minimum yield strength of 280 MPa. the bending load is F =1.5 kN, the axial load is P = 10kN and the twisting moment is T = 70 N-m. Determine the factor of safety based on the stress at point A using (a) the maximum shear stress theory and (b) the distortion...
A cable car weighs 2500 kg. The cable is made of steel of diameter 12 mm (Young's modulus of steel is 207 GPa). a) What is the strain in the cable? b) What is the extension in the cable when the cable length is 2.4 m? c) If the yield stress of the steel cable is 300 MPa, how many people can get in the lift car? Assume average weight of one person = 65 kg and Factor of Safety...
A concentrated load P is applied to the upper end of a 0.86-m-long pipe. The outside diameter of the pipe is D-106 mm and the inside diameter is d-98 mm. (a) Compute the value of Q for the pipe. (b) If the allowable shear stress for the pipe shape is 75 MPa, determine the maximum load P that can be applied to the cantilever beam. Answers: (a) Q = (b) P = kN A concentrated load P is applied to...
Stress Analysis 3. A 20-mm diameter rod made ofa ductile material with a yield strength of 350 MPa is subjected to torque of 100 N.m and a bending moment of 150 N.m. An axial force is then gradually applied. Determine the value of force when the rod begins to yield. Solve the problem two ways using the (a) Tresca theory (Maximum shearing stress theory) and (b) von Mises theory (Maximum distortion energy theory) [12+12 points 3. A 20-mm diameter rod...
A rigid beam ABCD is supported by a pin at B and two cables located at A and C. The cables have a 30 mm diameter and are made of steel with yield strength of 800 MPa and elastic modulus of 200 GPa. The beam is designed to resist a vertical load P applied at D equal to 200 kN. a) Find the forces developed in each cable b) Find the corresponding vertical displacement at point where the load is...
3 (15 points) A bent circular cantilever beam of uniform diameter of 25 mm is shown in igure below. The beam is made from a material with elastic modulus is 70 GPa, the tensile strength is 250 MPa, and the ultimate strength is 300 MPa. 250 mm A. 150 mm z Zz. 50N V (z direction) 100 N (a) (5 points) What are the stresses in the beam at point A? (b) (10 points) Based on your calculations in (a),...