Please help 1 ks2 Vinawa - To Vout * D2 S1k2 (i) Using Diode Model C...

Question

Question

Please help 1 ks2 Vinawa - To Vout * D2 S1k2 (i) Using Diode Model C shown below, find the range of input voltage so that D1 is off and D

Answer 1

Answer #1

To identify the state of the diode sieplace the diode with open circuit and find the Voltage across the diode, Hlie diode col

D, ON! 7 50 From the modal analys 11 ed V-0.75 6 lb 707 Live Vorpu Vo7075 No to 201 - the 20V 3 Vo = 20 +0.7 +5 Į Vo = 8:566

if you have any doubts please comment

if everything is clear please rate the answer

thank you

Answer 2

Similar Homework Help Questions

a) Use the constant voltage drop model for the diode and determine the input / output...

a) Use the constant voltage drop model for the diode and determine the input / output ratio (Vout x Vin), equations. Vdon = 0.7V, rz = 0Ω, Vz = 3V and R = R1 = R2 = 1000Ω. b) Draw the Vout x Vin graph. Highlight the slope coefficients of the lines and the coordinates of the points where the slope changes occur. D1 D2 DR3 Vin 7R1 Vout 214 22
This is a Diode constant voltage model - clipping circuits Please explain steps as you solve....

This is a Diode constant voltage model - clipping circuits Please explain steps as you solve. Thank you very much for your help. please ask if there is anything not clear about the problem W (a) For the circuit shown below use the constant voltage diode model (Vp=0.7 V), and find the state of diodes D, and D2 (ie. ON or OFF) and determine the voltage and the current for each. 32k2 OV 5 mA 103=_ ; VD3= 104= ;...
All used in the next circuit diodes are silicon. Zener of diode D2 the voltage is...

All used in the next circuit diodes are silicon. Zener of diode D2 the voltage is 8 V, the zener voltage of the D4 diode is 5.6 V It is given as. Applied input voltage Vin = 20 sin (ωt) is determined as V. Output of the circuit voltage changes according to the applied voltage of Vin Analyze the circuit and draw it. (Simplified of diode element model will be used.) (I can't analyze. Please explain) R + D D3...

4. For the circuit below, given that the resistor is I ΚΩ , the diode has...

4. For the circuit below, given that the resistor is I ΚΩ , the diode has a current vs. voltage function as shown, and n 2 V, A. What is the voltage at the negative ()input of the op amp? B. What will the current be through the diode (from Vin to the negative input of the op C. Sketch the function of Vout Vs. Vin for positivei D. What will the current be through the resistor (from Vin to...
2. Sketch Vout VS Vin and Vout if Vin-10sin(2TT60t) for each of the following circuits. You may a...

2. Sketch Vout VS Vin and Vout if Vin-10sin(2TT60t) for each of the following circuits. You may assume that the forward diode drops for the diodes equals zero Vout s v out Vin 5 V Vout out 3. Repeat problem 2 but with forward diode drops equal to 0.7 V 4. What are the primary mechanisms for current flow in a. A forward biased diode. b. A reverse biased diode not in breakdown. c. A reverse biased diode in breakdown...
(25 pts)For the circuit below assuming an ideal diode with a 0.7 V drop (You must...

(25 pts)For the circuit below assuming an ideal diode with a 0.7 V drop (You must fill in the information in the boxes below): a. Sketch Vout VS. Vin- b. When Vin -5V: Determine which diode leg is conducting, the current flowing through the diode, and Vout? c. Find the values in part b when Vin 0.3V? d. Find the values in part b when Vin 3V? R 1-2k, R2 = 6k. R1 R2 D2 Vout DI R2

For the diodes, use the models shown below; the regular diode model has 0.7V forward bias...

For the diodes, use the models shown below; the regular diode model has 0.7V forward bias voltage; the Zener diode model has -3V breakdown voltage Question 2 (25 points) For the diodes, use the models shown below; the regular diode model has 0.7V forward bias voltage; the Zener diode model has -3V breakdown voltage. a) Determine the minimum positive value of in to make D1 conduct current. (10 pts) b) Determine the minimum positive value of lin to make D2...
Please answer clearly Determine voltage characteristics (Vout/V) of the circuit shown in Figure 1. Assume: a)...

Please answer clearly Determine voltage characteristics (Vout/V) of the circuit shown in Figure 1. Assume: a) Diodes D1 and D2 are ideal. b) Zener diode has r2-0 with the break down voltage of Vz-12 V. 1ΚΩ D1 D2 추 R2 1ΚΩ Vout Figure 1
i need help plz For the diode circuit shown below, draw the V_OUT- V_IN (transfer) characteristic....

i need help plz For the diode circuit shown below, draw the V_OUT- V_IN (transfer) characteristic. Assume the ideal diode model for D1 and the constant-voltage model (with V_Don = 0.8V) for D2.