Three pipes are in parallel configuration with a total head loss of 20.3 m. The pipe data are:
Pipe | L (m) | D (m) | Absolute roughness (mm) | Relative roughness (Absolute roughness / D) |
---|---|---|---|---|
1 | 100 | 0.08 | 0.24 | 0.003 |
2 | 150 | 0.06 | 0.12 | 0.002 |
3 | 80 | 0.04 | 0.20 | 0.005 |
Use density = 1000 kg/m^3 and kinematic viscosity = 1.02 x 10^-6
m^2/s. Calculate the total flow rate. Neglect any minor
losses.
Show the working all the way to the final answer ΣQ = 0.02772 m^3/s
.
Three pipes are in parallel configuration with a total head loss of 20.3 m. The pipe...
C= 20 L/S
3. Neglecting minor losses in the pipe, determine the flows in the pipes and the pressure heads at the nodes (kinematic viscosity= 1.13x10 mº/s). Lengths and diameters of pipes are given in the table below. Roughness size of all pipes is 0.06 mm. Pressure head elevation at A point is 65 m od and the elevations of pipe nodes from A to F are 30, 25,20, 20, 22, and 25, respectively BE Pipe Length m) Diameter (mm)...
Consider a 100 mm internal diameter plastic pipe with a length of 1000 m and an absolute roughness of 0.01 mm. Assume the kinematic viscosity of water to be 1.14 mm2/s. a) What should the secondary loss coefficient k be to have a secondary loss one tenth of the friction loss at Re = 4000? [41] b) Calculate the friction, secondary and total head losses for the pipe at a Re = 105. Use the secondary loss coefficient found in...
39. (a) Water flows under gravity from Reservoir A to Reservoir B first through a 900-m long pipe (pipe a) and then through two pipes (b and c) in parallel. The lengths, diameters and friction factors of the pipes are listed in the table. The water level in Reservoir A is always higher than that in Reservoir B by 20 m. Calculate the total discharge between the reservoirs. Neglect all minor losses. (15 marks) (b) Which of pipes b and...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at an elevation 10 m above the reservoir surface. The mass flow rate is 40 kg/s and the volumetric flow rate is 0.040 m3/s. The large diameter inlet pipe total length is 50 m. The pump effidency is 65%. The longer smaller diameter pipe leaving the pump is 200 m in total length. The pipes have different diameters as indicated below. The...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
For the three connected reservoirs with the given information, calculate the water velocity in each pipe, neglecting the minor losses Patm Zв 850 f. =700 ft. d 1.1 ft Patm =800 ft. d 1 ft f=0.03 atm in all pipes ZA838 ft. d 1.2 ft =600 ft =805 ft. Datum F (velocity, ft/s x diameter. (Vd) for water at 6 Valu 8000 8 10 0.1 0.2 0.4 0.6 0.8 1 40 60 80 100 200 400 600 800 1000 2...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis 250 250 200 Stress (MPa) Stress (MPa) 150 $150 100 100 0 0 0 0.02 0.04 0.06 0.12 0.14 0.16 0.18 0 0.08 0.1 Strain 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 Strain (a) Determine the % elongation, yield stress and ultimate tensile strength of the material tested above (3 marks) (b) Calculate the elastic modulus of the material tested above...
Temperature Density °C kg/m3 0 999.82 5 1000.00 10 999.77 15 999.19 20 998.29 25 997.13 30 995.71 35 994.08 40 992.25 45 990.22 50 988.02 55 985.65 60 983.13 65 980.45 70 977.63 75 974.68 80 971.60 85 968.39 90 965.06 95 961.62 100 958.05 Dynamic viscosity kg/m.s 0.0017920 0.0015200 0.0013080 0.0011390 0.0010030 0.0008910 0.0007980 0.0007200 0.0006530 0.0005960 0.0005470 0.0005040 0.0004670 0.0004340 0.0004040 0.0003780 0.0003550 0.0003340 0.0003150 0.0002980 0.0002820 Kinematic viscosity mºs x 10-6 1.7923226 1.5200000 1.3083009 1.1399233 1.0047181...
example provided
parallel system and determine the 0.05 m/s flow distribution for a 4 parallel pipe system when Qin D, mm 50 75 100 125 L, m 50 100 150 200 Element 0.02 0.03 0.02 0.03 2.5 Assuming that 0 is known, the unknowns in the above equations are Q1, 02, and are solved simultaneously in the manner shown in the following example. and ΔΗ H,-H, EXAMPLE 10.4 Find the flow distribution and change in hydraulic grade line for the...