Question 6 In the differential amplifier shown in Fig. Qu6, R1 = 10k 2, R2 = 10k 2, R3 = 100k 2 and Rf = 100K22. Determine the output voltage Vo if: Vol 12 0² 777 Figure Qu 6 (a) V1 = 5mV and V2 = 0 (b) V1 = 0 and V2 = 5m V (c) VI = 50mV and V2 = 25mV (d) V1 = 25mV and V2 = 50m V. [3x4 marks]
Solve this circuit? Rf 10k О-15 R1 1k V. Vo ua741 15 Figura 5-3 Amplificador inversor para la práctica
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K2, R2=8 K12, R3=3.8 KS2, R4=6 KI2, R5=15 KS2, R6=3.8 KN, RL=9.8 K12, V1=1V, 12=0.5 mA and V3=2.2 V. } R6 R1 w R5 w + Vo + } RL 12 R2 V1 R3 R4 + +1 V3 Using the above circuit, but consider the following component values: R1= 2 KN R2=8 K2, R3=4.1 K12, R4=6 KI2, R5=17.0 K12, R6=15 KI, RL=10 KI, V1=1V, 12=0.5mA...
Given V1 = 1 Vpp, V2 = 4 Vpp, Vout = 0.82 Vpp and Rf = 2 kq and that R1, R2 and R3 are all equal, find the value of R1 Input resistor R1 = R2 = R3 = ko. (Round your answer to 2 decimal places) RF Vout OA1 R1 Sm R2 + TL081 L 1 : v2 3 R3 Use phasor techniques to determine the current supplied by the source given that V = 12 <0° v,...
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K2, R2=8 K2, R3=5.1 K2, R4=6 KN, R5=14 KN, R6=4.2 KS, RL=10.3 KS, V1=1V, 12=0.5 mA and V3=3.2 V. R6 R1 R5 Vo w + * RL + 12 R2 V1 R3 R4 V3 Answer: OV Using the above circuit, but consider the following component values: R1= 2 K12 R2=8 K2, R3=2.9 K2, R4=6 KI2, R5=10.8 K92, R6=15 KO, RL=10 K2, V1=1V, 12=0.5mA and V3=2V....
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K12, R2=8 KN, R3=3.9 KN, R4=6 KN, R5=18 K2, R6=4.4 KN, RL=12.5 KN, V1=1V, 12=0.5 mA and V3=3.4 V. R6 R1 R5 Vo + + RL R2 V1 R3 R4 + V3 Answer: LOV Using the above circuit, but consider the following component values: R1= 2 KO2 R2=8 K12, R3=3.6 K12, R4=6 K12, R5=16.9 KN, R6=15 KN, RL=10 KO, V1=1V, 12=0.5mA and V3=2V. What is...
1. Set up the following circuit. (20pts) 5 Vp-p R2 Vo Use the function generator to set up signal (5 Vpp sinusoidal with a 5 V DC offset) as the input voltage (Vin) and take the output voltage (Vo) across R Sketch and label the input voltage (Vin) and actual output voltage (Vo) displayed on the Oscilloscope and compare actual Vo to your calculated output Vo. (Show your all work for your calculation to get a full credit.) You should...
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 KS, R2=8 KN, R3=3.4 KA, R4=6 KN, R5=20 KN, R6=2.9 KN, RL=12.5 KN, V1=1V, 12=0.5 mA and V3=3.1 V. R6 R1 R5 VO + RL 12 R2 V1 R3 { R4 w V3 Answer: "V
Find V(t) R2 10K C1 100u C2-100u 10K Figure 15: Circuit for part C
Please find the thevenin equivalent first as suggested 3. In the circuit below, R1 10k, R2 20k and C 0.1uF. At t0, a step function of 10 V magnitude is applied to the input. Find V(t) at the output and sketch it. Your sketch should be quantitatively correct, that is, it should have labeled V and t axes. Strongly suggested: solve by first finding the Thévenin equivalent of the source voltage and resistor network Input (problem 3) 10V IN R2...