please show work. thank you very much.
Homework Answers
Add Answer to:
please show work. thank you very much.
Problem 4: The pre-cast T-beam has the cross-section shown....
A reinforced concrete beam of T-section is cast from N32 concrete. The beam has a flange...
A reinforced concrete beam of T-section is cast from N32
concrete. The beam has a flange width of 805mm, flange thickness
90mm, web width of 300mm and overall depth of 650mm. Two, N32
tensile rods with an effective cover of 46mm are located in web
area, and four, N20 compressive rods with an effective cover of
25mm are located in the flange area. The center-to-center distance
between the compressive rods is 225mm. The bending moment applied
to the section is...
A typical cross-section of a reinforced concrete beam is shown in Figure 1. The unit weight...
A typical cross-section of a reinforced concrete beam is shown in Figure 1. The unit weight the beam concrete along with the embedded reinforcement is estimated to be 150 lbs/ft3. 72 6 6 24" 8 48 12 18 Figure 1. Typical Beam Section All Dimensions are in Inches The beam has uniform cross-section throughout its entire length and simply supported over a span (L) of 30 ft. Calculate the following due to self-weight only: (a) Self weight of the beam...
L MetroPCS 12:08 AM 1 27% Back Problem 3 6. The span length and cross section of e are shown. The...
l MetroPCS 12:08 AM 1 27% Back Problem 3 6. The span length and cross section of e are shown. The beam is ue The concrete and reinforcing steel 3100 lbf/in, f, = 35,000 lbf/in. and A,ミ2.5 are 4 ft live load, P dead load, Wo7 lbf/ft 9.5 in 16 in 13 in steel reinforcing bars beam cross 8 ft The balanced reinforcing steel ratio for this beam accordance with ACI specifications is most nearly (A) 0.037 (B) 0.046 (C)...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it is subjected to a bending moment of M = 60 kip ft determine the normal stress in each of the steel reinforcing rods and the maximum normal stress in the concrete. Take Est = 29(10) ksi and Econc = 3.6(103) ksi SOLUTION Since the beam is made of concrete, in the following analysis we will neglect its strength in supporting...
a hundred random draw with replacement are taken from box A reinforced concrete beam has square cross section (h x h) h- 280mm. There are 6 steel reinforcing bars (each of diameter d-25mm), 3 e...
a hundred random draw with replacement are taken from
box
A reinforced concrete beam has square cross section (h x h) h- 280mm. There are 6 steel reinforcing bars (each of diameter d-25mm), 3 evenly spaced towards the top, and 3 evenly spaced towards the bottom. The vertical distance from the center of the bar to top (or bottom) edge of the section is called the cover, and is denoted as e 45mm. It should be taken that psteel-7850 kg/m3,...
A cantilever cast-iron beam is 6 ft long and has a “T” cross section, as shown....
A cantilever cast-iron beam is 6 ft long and has a “T” cross section, as shown. Calculate the maximum tensile and compressive bending stresses. The applied load is 450 lb. Neglect the weight of the beam. Show the diagram of both (Tensile and Bending stresses at the section area). 450 lb 60" (a) Load diagram (b) Section A-A
Could you please help me on question 7. Thank you very much. The floor system shown...
Could you please help me on question 7.
Thank you very much.
The floor system shown below consists of normalweight concrete (150 pcf). Beams C2 ! LT 1 7.0 inch ! h=20 in G2! 12 in Girders BI 1 7.0 inch Slab 8 ft span h 24 in ----- - -- - --- 15 in 15 ft 15 ft Use 4000 psi concrete and Gr. 60 reinforcing steel. Assume 0.75 inch clear cover. Include concrete self-weight and a superimposed dead...
10. A beam cross-section is limited to the size shown below. Determine the required area of...
10. A beam cross-section is limited to the size shown below. Determine the required area of reinforcement for service load moments Mp-430 ft-kip and M 175 ft-ki ksi. Note that the beam self weight is already included in the dead load moment. Assume that c 0.6c for the singly-reinforced part of the section (for your initial guess). Hint: first calculate the nominal moment resisted by the concrete section without compression steel. Check the strength only p.f -4,000 psi and f,-60...
please show all your work thank you! Problem 2 (25%) 14 in A beam cross-section is...
please show all your work thank you!
Problem 2 (25%) 14 in A beam cross-section is shown in the provided figure. 2 in (A)(10%) Determine the distance (y) from the bottom the section to the centroid (C). 16 in 8 in Problem 2 (25% - 14 in- A beam cross-section is shown in the provided figure. 2 in (B) (15%) Determine the moment of inertia of the shape about the X-axis (i.e. the horizontal centroidal axis) 16 in - 2...
Reinforced concrete Problem #1 (40 points): A beam with x-section shown in the figure is made...
Reinforced concrete
Problem #1 (40 points): A beam with x-section shown in the figure is made out of concrete with compressive strength fc = 4000 psi and the steel reinfrocemnt is of Grade 60 (fy 60000psi). Determine 1 The maximum compressive stress in the concrete f and the tensils stress in the steel , if the section is subjected to a bending moment of 130 ft-k (assume n 8) N.A._ 23" 23-х 4 #10 (5.06 in. 3" 18"
A reinforced concrete beam of T-section is cast from N32
concrete. The beam has a flange width of 805mm, flange thickness
90mm, web width of 300mm and overall depth of 650mm. Two, N32
tensile rods with an effective cover of 46mm are located in web
area, and four, N20 compressive rods with an effective cover of
25mm are located in the flange area. The center-to-center distance
between the compressive rods is 225mm. The bending moment applied
to the section is...
A typical cross-section of a reinforced concrete beam is shown in Figure 1. The unit weight the beam concrete along with the embedded reinforcement is estimated to be 150 lbs/ft3. 72 6 6 24" 8 48 12 18 Figure 1. Typical Beam Section All Dimensions are in Inches The beam has uniform cross-section throughout its entire length and simply supported over a span (L) of 30 ft. Calculate the following due to self-weight only: (a) Self weight of the beam...
l MetroPCS 12:08 AM 1 27% Back Problem 3 6. The span length and cross section of e are shown. The beam is ue The concrete and reinforcing steel 3100 lbf/in, f, = 35,000 lbf/in. and A,ミ2.5 are 4 ft live load, P dead load, Wo7 lbf/ft 9.5 in 16 in 13 in steel reinforcing bars beam cross 8 ft The balanced reinforcing steel ratio for this beam accordance with ACI specifications is most nearly (A) 0.037 (B) 0.046 (C)...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it is subjected to a bending moment of M = 60 kip ft determine the normal stress in each of the steel reinforcing rods and the maximum normal stress in the concrete. Take Est = 29(10) ksi and Econc = 3.6(103) ksi SOLUTION Since the beam is made of concrete, in the following analysis we will neglect its strength in supporting...
a hundred random draw with replacement are taken from
box
A reinforced concrete beam has square cross section (h x h) h- 280mm. There are 6 steel reinforcing bars (each of diameter d-25mm), 3 evenly spaced towards the top, and 3 evenly spaced towards the bottom. The vertical distance from the center of the bar to top (or bottom) edge of the section is called the cover, and is denoted as e 45mm. It should be taken that psteel-7850 kg/m3,...
A cantilever cast-iron beam is 6 ft long and has a “T” cross section, as shown. Calculate the maximum tensile and compressive bending stresses. The applied load is 450 lb. Neglect the weight of the beam. Show the diagram of both (Tensile and Bending stresses at the section area). 450 lb 60" (a) Load diagram (b) Section A-A
Could you please help me on question 7.
Thank you very much.
The floor system shown below consists of normalweight concrete (150 pcf). Beams C2 ! LT 1 7.0 inch ! h=20 in G2! 12 in Girders BI 1 7.0 inch Slab 8 ft span h 24 in ----- - -- - --- 15 in 15 ft 15 ft Use 4000 psi concrete and Gr. 60 reinforcing steel. Assume 0.75 inch clear cover. Include concrete self-weight and a superimposed dead...
10. A beam cross-section is limited to the size shown below. Determine the required area of reinforcement for service load moments Mp-430 ft-kip and M 175 ft-ki ksi. Note that the beam self weight is already included in the dead load moment. Assume that c 0.6c for the singly-reinforced part of the section (for your initial guess). Hint: first calculate the nominal moment resisted by the concrete section without compression steel. Check the strength only p.f -4,000 psi and f,-60...
please show all your work thank you!
Problem 2 (25%) 14 in A beam cross-section is shown in the provided figure. 2 in (A)(10%) Determine the distance (y) from the bottom the section to the centroid (C). 16 in 8 in Problem 2 (25% - 14 in- A beam cross-section is shown in the provided figure. 2 in (B) (15%) Determine the moment of inertia of the shape about the X-axis (i.e. the horizontal centroidal axis) 16 in - 2...
Reinforced concrete
Problem #1 (40 points): A beam with x-section shown in the figure is made out of concrete with compressive strength fc = 4000 psi and the steel reinfrocemnt is of Grade 60 (fy 60000psi). Determine 1 The maximum compressive stress in the concrete f and the tensils stress in the steel , if the section is subjected to a bending moment of 130 ft-k (assume n 8) N.A._ 23" 23-х 4 #10 (5.06 in. 3" 18"
Most questions answered within 3 hours.
-
The current risk-free rate is 4.0% and the market risk premium
is 5.0%. If Ford Motor...
asked 7 minutes ago -
Advances in technology have increased our opportunities to
connect with others. Along with the benefits of...
asked 15 minutes ago -
Compute the interest rate at which $500 per month payments
should grow to accumulate savings of...
asked 16 minutes ago -
The following information pertains to a weekly payroll of Texera
Tile Company:
a. The total wages...
asked 18 minutes ago -
Alice has the RSA public key (n, e) = (11413, 251) and private
key d =...
asked 31 minutes ago -
QUESTION 5
A drug or medicine can reach the brain more effectively by
placing the drug...
asked 35 minutes ago -
Developmental biology
A mouse contains a mutation that results in a failure of their
long
bones...
asked 31 minutes ago -
Rammazzotti, Inc., is looking for feedback on company
performance. The company compares the budget for the...
asked 36 minutes ago -
A manufacturer of chocolate chips would like to know whether its
bag filling machine works correctly...
asked 45 minutes ago -
Consider the student registration business process at
your college:
1.)Describe the steps necessary for you to...
asked 52 minutes ago -
when released from rest at point A, an unknown ion moves to
point B. At point...
asked 44 minutes ago -
A stock is expected to pay the following dividends: $1.1
four years from now, $1.4 five...
asked 49 minutes ago