PROBLEM 2 (10 pts.) An Ideal DC motor has a no load (free running) speed of...
A 12-pole, brushless, DC motor has a no-load speed of 5000rpm and a stall torque of 50 in-oz when operating at rated voltage of 60V. Testing shows that no-load speed and stall torque vary linearly with applied voltage. Also, with a constant applied voltage the speed decreases linearly as delivered torque increases. Calculate the following: Torque that the motor delivers at 2000 rpm when operated at rated voltage. T a) b) Fundamental frequency of the applied voltage waveform at this...
A 220 V DC shunt motor has an armature resistance, Re-0.1 S2, a field resistance, Ry=100 12, and negligible rotational losses. Under certain load conditions, the shunt motor runs at 1600 rpm while drawing a total current, I = 100 A. Determine: a. the output power of the motor; b. the output torque in N-m; and, c. the efficiency Without making any changes to the applied voltage or the field, the motor operates with a new M mechanical load that...
For a PMDC motor powered by a 12 V DC source, the no-load speed and stall torque are 3800 RPM and 30 mNm, respectively. If the motor is running at 2500 RPM, find a) Shaft torque (Tshaft), b) Rotor current (Im), c) Back emf (Eb), d) Electrical power consumed, e) Shaft power, and f) Power loss in rotor coil.
need the answer for the question no. 1 ENGR 113 Homework DC Motor Objectives Plot the Torque-Speed curve for a given DC motor given the stall torque and no load speed values Calculate the rotational power for a DC motor given the stall torque and no load speed values Plot the rotational power on a Torque-Speed curve to see the relationship between torque, speed, and power Calculate the maximum efficiency of a DC motor. Calculate the operating point for a...
If a manufacturer's specifications for a PM DC motor are as follows, what are the motor's no-load speed, stall current, starting torque, and maximum power for an applied voltage of 10 V? ■ Torque constant 0.12 Nm/A Electrical constant 12 V/1000 RPM Armature resistance-: 1.5 Ω
A separately excited DC motor is fed from a variable DC source and it drives a variable mechanical load as shown in Figure Q4b. The excitation current If is held constant during the motor operation. (i) How can the motor direction be reversed? (4 marks) (ii) Explain what will happen to the current Ia, the internal voltage Eg, and speed if the mechanical torque increases whilst the DC input voltage VT is held constant. (4 marks) (iii)Explain what will happen...
1. A shunt machine, while running as a generator, has an induced voltage of 260 V at 1200 rpm. Its armature and field resistances are 0.2 2 and 110 Q, respectively. If the machine is run as a shunt motor, it takes 4 A at 220 V (i) Draw the schematic diagram of the machine as a generator. (ii) Draw the schematic diagram of the machine as a motor (iii)At a certain load the motor takes 30 A at 220...
A particular dc motor has the following specifications: nominal voltage: 12V, no load RPM 19300, no load current 1.4A, rated rpm 17100. Find torque, power, and linear and/or angular velocity.
An armature-controlled dc motor operates at steady state, with an armature drive voltage va = 10 V. The motor runs at 600 rpm, and the armature current is found to be ia = 0.2 A. The armature resistance is Ra = 15 Ω. Determine: (a) The torque constant km of the motor (b) Electrical damping constant be (c) The efficiency under the given operating conditions, if the mechanical damping constant is bm = 8.25 × 10−5 N ⋅ m/rad/s (d)...
I can not seem to get the right answers. Thank you! Given a 1/4 hp, separately excited, dc motor with the following parameters: K = 0.61, R, 15Ω, La-120mb. J = 0.005, and b = 0.0006. The armature voltage is controlled by a 120-V dc PWM source operating at 100 Hz 1. What is the armature current if the no-load speed is 1800 rpm when the armature supply is operated at a 100% duty cycle? 2. What is the no-load...