NaCl=20.9 C KCl=20.4 C CaCl2=20.4 C III. Calculations Given the following thermodynamic data, calculate AHⓇ, AS,...
Using the thermodynamic data given in the procedure, calculate ∆H°, ∆S°, and ∆G for the dissolution of each salt in Part 1. Use the initial temperature you recorded in lab for the ∆G calculation. Data Table 1 Salt Observations Mass of Salt (g) Volume of Water (ml) 5.0 Initial Final Temperature Temperature (°C) (°C) 1.0173 23.1 21.9 Sodium Chloride completely dissolved, slightly cooler 5.0 1.0233 22.8 15.2 Potassium Chloride completely dissolved, cold to the touch 5.0 0.9824 23.2 30.7 Calcium...
- T 2 31 5 6 Using the thermodynamic data given in the procedure, calculate AH°, AS, and AG for the dissolution of each salt in Part 1. Use the initial temperature you recorded in lab for the AG calculation. AH (kJ/ S (J/mol K) mol) Salt Observations Volume of Water (ml) 5.0 Mass of Salt (g/ Initial Final Temperature Temperature 411.1 72.12 Sodium Chloride 1.0173 23.1 219 82 NaCl) KCI (5) CaCl (s) Nat(a) 436.7 -795.4 completely dissolved slipy...
The first picture is used for question #2, and question #3 can be normally answered. I believe the answer to question 3 is -> 0.07144M. However I would like someone to check it. I am not sure about 2. BE SURE THAT YOU RECORD ALL OF YOUR DATA AND LABEL PROPERLY FOR PARTI OF THIS LABORATORY EXPERIMENT. YOU WILL NEED TO ACCESS THIS INFORMATION IN THREE WEEKS. Part I Synthesis of the Complex Salt containing Copper Procedure 16.004 1. In...
____ Reaction workup details (role of K2CO3,Na2S2O3, brine)? HYDROBORATION-OXIDATION OF 1-HEXENE 1. In a screw cap V-vial, prepare a solution of 0.33 g of iodine in 3 mL of dry THF. Firmly tighten the cap; keep the vial closed until ready to use. 2. In a 25 mL round-bottom flask, weigh 0.12 g of sodium borohydride. Add 8 mL of dry THF; stopper the flask with a septum, and stir the mixture for 10 min at room temperature 3. Prepare...
____ What was the purpose of hydrogen peroxide and why was it added slowly with cooling? HYDROBORATION-OXIDATION OF 1-HEXENE 1. In a screw cap V-vial, prepare a solution of 0.33 g of iodine in 3 mL of dry THF. Firmly tighten the cap; keep the vial closed until ready to use. 2. In a 25 mL round-bottom flask, weigh 0.12 g of sodium borohydride. Add 8 mL of dry THF; stopper the flask with a septum, and stir the mixture...
need help with calculations V. Heat of reaction for NaOH (s) + HCI (aq) → Naci (aq) + H20 ()-dH(net) Direct determination Mass NaOH Moles NaOH = moles Mass of HCI solution Final temp. of solution Initial temp. of solution AT solution 30 23 C 4 C AH(net)(Direct) per mole NaOH Calculation Indirect determination Heat of dissolution of NaOH (s) [AH(diss)] Mass NaOH Moles NaOH moles Mass of water Final temp. of solution Initial temp. of solution AT solution AH(diss)-...
10. When sodium chloride dissolves in water, the ions dissociate: NaCl (s) = Na+ (aq) + Cl- (aq) Write ionic equations, similar to the one above, that describe how NaNO3 and NaCH3CO2 each dissociate as they dissolve in water. Include heat as a reactant or product in each equation. Here is what I answered: NaNO3 (s) = Na+ + NO3- + heat NaC2H3O2 + Heat = Na+ + C2H3O2-(ag) Lab data table attached to determine where to place heat. AGO no...
Determine the percent yield of copper. 3. What is the theoretical yield of copper produced by this reaction? Materials: Copper (II) chloride • Aluminum foil • Stirring rod • Two 100 ml beakers • Graduated cylinder • Safety glasses • Spatula or scoopula • Balance Filter paper front counter Funnel • Watch glass Ring stand • Iron ring Safety: Safety glasses must be worn at all times! Copper (II) chloride is an irritant and moderately toxic. Avoid inhaling the powder...
Oxalic addindate CH2OT-2H2 Fill out the table with the appropriate data from Part C, Trial 1 Trial 2 439 Mass of Oxalic Acid Dihydrate (g) Moles of Oxalic Acid Dihydrate (Convert grams of oxalic acid to moles using the molecular weight of oxalic acid dihydrate) Moles of NaOH (Convert moles of Oxalic Acid Dihydrate to moles of NaOH using the mole ratio from the reaction) 25mL 41.6mL 41.35 mL Initial burette reading (mL) 2omL 32.00ML Final burette reading (mL) Volume...
calculate the % yield fir the n-butylacetate synthesis. show how you obtained expected yield. Mass of final product was 3.4g INSTRUCTIONS A. SETTING UP THE EXPERIMENT This wetion was completed during Experiment D. Proceed to Part B. anol) and 0.75 mL concentrated H2SO4 1. GOGGLES AND GLOVES. Carefully pour the following materials into a flask: 5 ml glacial acetic acid, 4.5 mLn-butanol (1-butanol) and 0.75 ml 2. Swirl carefully to mix the components thoroughly. 3. Seal the flask well (cork...