Water flows in a pipe 1.7 cm in diameter and 480 cm long at a velocity...
1. Water (at 70 o C) flows with a velocity of 1 m/s in a 2 cm diameter pipe. The pipe wall temperature is at 100 o C. (a) What is the heat transfer from the pipe wall to the fluid? (b) Determine the critical velocity at which the flow would be characterized as laminar and for this flow velocity calculate the heat transfer (c) Assume the diameter of the pipe is doubled while all other conditions remain the same....
Water flows in a 7.4 cm diameter pipe at a velocity of 0.67 m/s. The mass flow rate in kg/s of water in the pipe is:
(15 points) Please show your work! Water (p = 1000 kg/m3) flows through the pipe below. The pressure at point A is 300 kPa. Determine the x and y components of force the water exerts on the horizontal assembly. The pipe has a diameter of 2.5 cm at A, and at B and C the diameter is 1 cm. The water is discharged into the atmosphere at B and C. Neglect frictional losses. Dc = 1 cm A B Da...
Water flows in a 20 cm diameter pipe at 5 m/s as shown in Fig. A.4. It exits by impacting upon a 90- cone and leaves with a uniform flow of thickness 1 cm around the cone edge. (a) Calculate the force acting on the cone. (15 marks) (b) If the flow exits non-uniformly, explain how the movement of the cone will be affected. (5 marks) A.4 Water flows in a 20 cm diameter pipe at 5 m/s as shown...
Water flows at speed of 6 m/s through a horizontal pipe of diameter 3.5 cm. The gauge pressure P1 of the water in the pipe is 1.7 atm. A short segment of the pipe is constricted to a smaller diameter of 2.4 cm . What is the gauge pressure of the water flowing through the constricted segment? Atmospheric pressure is 1.013 × 10^5 Pa. The density of water is 1000 kg/m^3 . The viscosity of water is negligible. Answer in...
A Review Water in the reservoir flows through the 8-in.-diameter pipe at A into the turbine as shown in (Figure 1). Part A If the discharge at B is 600 ft/min, determine the power output of the turbine. Assume the turbine runs with an efficiency of 50%. Neglect frictional losses in the pipe. Express your answer using three significant figures. O AL "vec oi? Wout = hp Figure < 1 of 1 Submit Request Answer Provide Feedback Next > 36...
Water is delivered to a 4.0 cm diameter fountain head from a 6.9 cm diameter pipe that is 3.4 m below the fountain head and at a pressure of 94 kPa. The fountain head shoots the water straight up into the air. Neglect all losses. a.) What is the velocity of water coming out of the fountain head? Hint: Must use Bernoulli AND Continuity b.) What is the volume flow rate of the water through the fountain head? Hint: Q=vA
Water is flowing through a 10-cm diameter water pipe at a rate of 0.2 m^3/s. Now a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water that exits into the atmosphere, as shown. Disregarding frictional effects, determine the force exerted on the flange due to the water flow. Density of water = 1,000 kg/m^3. + d = 10 cm D = 20 cm Diffuser
A.4 Water flows in a 25 cm diameter pipe at 3 m/s as shown in Fig. A.4. It exits by impacting upon a 90°- cone and leaves with a uniform flow of thickness 1 cm around the cone edge. Water Flow out Water Flow in Cone V = 3 m/s diameter 40 cm Water Flow out 1 cm Fig. A.4 (a) Calculate the force acting on the cone. (15 marks) (b) If the flow exits non-uniformly, explain how the movement...
Steam enters a horizontal 14-cm-diameter pipe as a saturated vapor at 5 bar with a velocity of 10 m/s and exits at 4.5 bar with a quality of 95%. Heat transfer from the pipe to the surroundings at 291K takes place at an average outer surface temperature of 400 K. For operation at steady state, determine (a) the velocity at the exit, in m/s. (b) the rate of heat transfer from the pipe, in kW.? (c) the rate of entropy...