In a separately excited DC motor, the field voltage is much bigger than the armature input...
In a separately excited DC motor, the field voltage is much bigger than the armature input voltage. What is the problem in which the motor can be?
Homework Answers
Add Answer to:
In a separately excited DC motor, the field voltage is much
bigger than the armature input...
A separately-excited DC traction motor of a metro train is in series connection, i.e., the armature...
A separately-excited DC traction motor of a metro train is in series connection, i.e., the armature and the field windings are connected in series with a common DC power source. The voltage of the DC power source is I (a) Please show that the angular velocity of the rotor is KT K where o is the is the angular velocity of the rotor, Ra is the resistance of the armature, Rris the resistance of the field windings, T is the...
Q1. Draw the equivalent circuits of a separately excited and a shunt DC motor. [20] Q2....
Q1. Draw the equivalent circuits of a separately excited and a shunt DC motor. [20] Q2. Derive the speed-torque relation for a DC motor: [40] 0 = VR, Kø (KØ)??ind Q3. A DC motor's speed can be controlled by either changing the field resistance, changing the armature voltage or changing the armature resistance. Of these three, which one is the best method for DC motor speed control and which is the worst? Give reasons. [40]
Problem 2 A separately excited DC motor is characterized by the followng intormation Armature res...
Problem 2 A separately excited DC motor is characterized by the followng intormation Armature resistance Ra-5 2 armature inductance La . very large, Field resistance RS200 Ω, ted voltage Vt 200 V, and an inertia constant J-12 kg m Neglecting friction losses and assuming no-saturation in the machine magnetic core system, answer the folowing questions: Part 1: (6 marks) he motor a as shown in figure 2a. The motor drives a constant power load of vaue 1 40375 hp (ie...
A 250V, 50A separately excited DC motor has armature resistance of 0.8 ohms (including brushes) and...
A 250V, 50A separately excited DC motor has armature resistance of 0.8 ohms (including brushes) and field resistance of 100 ohms. Kf for this motor is 1.5 V/(A.rad/sec). The armature circuit can carry up to 50A for a short time period. It is desired to run it with a 250 V voltage source in no load conditions with the speed of 1500 r/min. a) Explain the required equipment and steps. b) Draw the circuit for steady-state operation with the speed...
A separately-excited dc motor with the following parameters: Ra = 0.25 ohm, La = 0.003H, and...
A separately-excited dc motor with the following parameters: Ra = 0.25 ohm, La = 0.003H, and Kb = 0.35 V/rad/sec. is driving a load of 1-0.0155 ke-m2, B -0.004 Nm/rad/sec with a load torque of 120 Nm. Its armature is connected to a dc supply voltage of 450 V and is given the rated field power. Determine the armature input power of the motor and choose the right answer from the given answer options. 120.5 kW 450 kW 159.6 kW...
(i) A 220 volts, 825 rpm, 125 A separately excited DC motor has an armature resistance...
(i) A 220 volts, 825 rpm, 125 A separately excited DC motor has an armature resistance of 0.05 2. It is fed from a single phase fully controlled rectifier with an ac source of 225 Volts, 50Hz. Assuming continuous conduction calculate (a) Firing angle for 1/4"hrated motor torque and 750 rpm (b) Motor speed for a=160 degrees and rated torque 5 Marks (ii) Draw and explain with neat circuit diagram of a DC drive circuit, which works with positive output...
A separately excited DC motor is fed from a variable DC source and it drives a...
A separately excited DC motor is fed from a variable DC source and it drives a variable mechanical load as shown in Figure Q4b. The excitation current If is held constant during the motor operation. (i) How can the motor direction be reversed? (4 marks) (ii) Explain what will happen to the current Ia, the internal voltage Eg, and speed if the mechanical torque increases whilst the DC input voltage VT is held constant. (4 marks) (iii)Explain what will happen...
separately excited series, shunt, compound DC motor: *Describe how does decreasing the field current IF affect...
separately excited series, shunt, compound DC motor: *Describe how does decreasing the field current IF affect the speed versus voltage characteristic and constant K1 of a separately-excited dc motor. K1=(n2-n1)/(E2-E1) *Describe how does decreasing the field current IF affect the torque versus current characteristic and constant K2 of a separately-excited dc motor? k2=(T2-T1)/(I1-I2) *Briefly describe how the speed varies as the mechanical load applied to the series motor increases, i.e. as the motor torque increases.
2. A dc chopper is used for regenerative braking of a separately excited dc motor. The...
2. A dc chopper is used for regenerative braking of a separately excited dc motor. The dc supply voltage is 400V. The motor has ra=0.2 ohms. Km=1.2 V-s/rad. The average armature current during regenerative braking is kept constant at 300A with negligible ripple. For a duty cycle of 60% for a chopper , determine a) Power returned to the supply. b) Minimum and maximum permissible braking speeds and c) Speed during regenerative braking.
A 230 V, 1000 rpm, 30 A separately excited motor has armature resistance and inductance of...
A 230 V, 1000 rpm, 30 A separately excited motor has armature resistance and inductance of 0.7 Ω and 50 mH respectively. Motor is controlled in regenerative braking by a chopper operating at 800 Hz from a dc source of 230 V. Assuming continuous conduction a) Calculate duty ratio of chopper for rated torque and the speed of 800 rpm. b) What will be the motor speed for duty ratio of 0.6 and rated motor torque? c) What will be...
A separately-excited DC traction motor of a metro train is in series connection, i.e., the armature and the field windings are connected in series with a common DC power source. The voltage of the DC power source is I (a) Please show that the angular velocity of the rotor is KT K where o is the is the angular velocity of the rotor, Ra is the resistance of the armature, Rris the resistance of the field windings, T is the...
Q1. Draw the equivalent circuits of a separately excited and a shunt DC motor. [20] Q2. Derive the speed-torque relation for a DC motor: [40] 0 = VR, Kø (KØ)??ind Q3. A DC motor's speed can be controlled by either changing the field resistance, changing the armature voltage or changing the armature resistance. Of these three, which one is the best method for DC motor speed control and which is the worst? Give reasons. [40]
Problem 2 A separately excited DC motor is characterized by the followng intormation Armature resistance Ra-5 2 armature inductance La . very large, Field resistance RS200 Ω, ted voltage Vt 200 V, and an inertia constant J-12 kg m Neglecting friction losses and assuming no-saturation in the machine magnetic core system, answer the folowing questions: Part 1: (6 marks) he motor a as shown in figure 2a. The motor drives a constant power load of vaue 1 40375 hp (ie...
A separately-excited dc motor with the following parameters: Ra = 0.25 ohm, La = 0.003H, and Kb = 0.35 V/rad/sec. is driving a load of 1-0.0155 ke-m2, B -0.004 Nm/rad/sec with a load torque of 120 Nm. Its armature is connected to a dc supply voltage of 450 V and is given the rated field power. Determine the armature input power of the motor and choose the right answer from the given answer options. 120.5 kW 450 kW 159.6 kW...
(i) A 220 volts, 825 rpm, 125 A separately excited DC motor has an armature resistance of 0.05 2. It is fed from a single phase fully controlled rectifier with an ac source of 225 Volts, 50Hz. Assuming continuous conduction calculate (a) Firing angle for 1/4"hrated motor torque and 750 rpm (b) Motor speed for a=160 degrees and rated torque 5 Marks (ii) Draw and explain with neat circuit diagram of a DC drive circuit, which works with positive output...
Most questions answered within 3 hours.
-
Wildhorse Company follows the practice of pricing its inventory
at the lower-of-cost-or-market, on an individual-item
basis....
asked 25 minutes ago -
3. (10 pts) You grow a corn crop that yields 150 bushels ac-1,
with the following...
asked 14 minutes ago -
7. The term Six Sigma refers to:
Select one:
a. The control limits established in a...
asked 23 minutes ago -
For the following reaction: A(g) + 2 B(g) ⇌ 2 C(g) Calculate the
equilibrium constant K...
asked 26 minutes ago -
Which of the following best describes tidal volume? options:
1.The amount of oxygen in the air...
asked 42 minutes ago -
1. Smaller cost distortions occur when the traditional systems'
single indirect-cost rate and the activity-cost-driver rates:...
asked 50 minutes ago -
Using either a FMECA approach or some other appropriate RCA
tool, identify five risk treatment actions...
asked 50 minutes ago -
If for a test the P-value is between 0.0025 and 0.005, what
conclusion can you draw?...
asked 1 hour ago -
Using Python. Write a function clean2(aList) that takes a list
of integers aList as argument, and...
asked 1 hour ago -
Intrapreneurship is defined as the
development of an enterprise culture with an existing (Nandan,
2009). An...
asked 1 hour ago -
QUESTION 1 Tamiflu is a drug used to treat influenza. A study
found that Tamiflu reduced...
asked 1 hour ago -
Which of the following would be less likely to be used to
allocate factory overhead when...
asked 1 hour ago