Question

For the problem below, calculate the overall gear ratio, output speed, direction of rotation for the output, output torque, i

0 0
Add a comment Improve this question Transcribed image text
Answer #1

ahout van AS No = 25 Nac. 50 . Ncc 30 . No a to NE= 20 Nee ho Solution: Win=17250pm Pin a 2009.965 W (1) Osciall gear ratio:2609.96= 2 x nx 1725 x Tm Go Tim : 120.448 N-m ] Ne . cm Output Porque: (Tout)...; Tout = GRA Tim. E &x Thottf Tout = 115.5841. Then, Tha: 115.584- Iteleted TA = 101.136 Nm) lj isput is anticlockwise. Onliput is clockwise (i) Output power: ... Pout -

Add a comment
Know the answer?
Add Answer to:
For the problem below, calculate the overall gear ratio, output speed, direction of rotation for the...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Compute the output speed and direction of rotation of the output shaft for the gear train...

    Compute the output speed and direction of rotation of the output shaft for the gear train shown in the figure. The input shaft rotates at 1750 rpm clockwise. NA 20 Only pitice of how NA 70 Ne Nos BU Output

  • Compute the output speed and direction of rotation of the output shaft for the gear train...

    Compute the output speed and direction of rotation of the output shaft for the gear train shown in the figure. The input shaft rotates at 1750 rpm clockwise. 20 pite clined open shown Onb NO Shafts Output (a) Side (6) End view

  • Machine design 1 Name Application 10 The compound reverted gear train shown below is used to...

    Machine design 1 Name Application 10 The compound reverted gear train shown below is used to reduce the speed of the input (gear 2) to the output gear 5. Your objective is to develop a design for this gear train be specify the gear teeth. There are several requirements to keep in mind and the objective is to reduce the overall size dimension Y Requirements . . . . Shall deliver 20 HP Input speed shall be 1750 RPM (adjustable)...

  • 1: Given the power transmission system shown below Input: 30 hp, 2,000 rpm 12 pitch 18...

    1: Given the power transmission system shown below Input: 30 hp, 2,000 rpm 12 pitch 18 teeth N C Rotation Hydraulic Pump 5 hp Water Pump, 6 hp 20° pressure angle 8 pitch 20 teeth 20° pressure angle 27 teeth 40 teeth Input Pump Output Bearing (typical) p (NP) Find: A Determine the rotation direction, rotational speed, and pitch diameter of each gear Pitch Diameter (in) Rotational Speed (rpm) Gear 1333 rmp B. Determine the hp and torque in shaft...

  • 2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

    2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. i) What is the ratio of output torque (Gear 4) to input torque (Gear 1)? j) Is it a coincidence that it is the same as the answer in 1 An input shaft drives Gear 1 with 20 teeth at 1800 rpm which mates with the 80-tooth Gear...

  • Problem 2: 50pts To monitor the rotation speed of a shaft, a generator motor attachment has...

    Problem 2: 50pts To monitor the rotation speed of a shaft, a generator motor attachment has been suggested. Here a permanent magnet motor, shown below, is directly attached to the shaft. Stator (magnet) Armature winding Bearing Power supply Brush Commutator Rotor A voltmeter is connected to the power supply connection and is calibrated for various voltage-rpm values. a) Determine the governing equations for this system. (use the motor rotation as the input and the voltage generated as the output) b)...

  • The top half of a compound epicyclic gear set is as shown in Figure Q2. If...

    The top half of a compound epicyclic gear set is as shown in Figure Q2. If the input shaft I rotate at dockwise direction at a speed of 1,200 rpm and gear Al is set as the output, determine the following. (a) The output speed Nal when gear X rotates counter-clockwise direction at the speed of 3,000 rpm. (b) The magnitude and direction of the torque required to lock gear X if 300 Nm torque is applied on input shaft...

  • Design Problem Design a speed reducer gear box that will take 1.5 kW power from an...

    Design Problem Design a speed reducer gear box that will take 1.5 kW power from an electric motor rotating at 3000 rpm (clockwise) and deliver it to a machine which operates at 2 different speeds, 1000 rpm (clockwise) and 500 rpm (counter-clockwise). Use Spur Gears with 20° pressure angle and 5mm module. Gear box should be of smallest possible size. The gear shift mechanism is not the part of the design A 2-speed double-reduction speed reducer is shown in the...

  • If using a two-stage planetary gear train, determine the output torque of each shaft In the...

    If using a two-stage planetary gear train, determine the output torque of each shaft In the proposed plan, an electromotor with a maximum power of 17kw at 1455 rpm is used to supply a gearbox with two output shafts connected to the mills. The motor is connected to the gearbox through a coupling system. Based on the required performance for the system, the first output shaft needs to transmit a power of at most 35% at 365 rpm to the...

  • Not really sure how to solve this problem. It is a planetary gear/ a compound gear.

    Not really sure how to solve this problem. It is a planetary gear/ a compound gear. The motor is driven at 800 RPM. What is the output speed and direction of Shafts 1 and 2? b. J-42 8-40 C-20 F-12 G-72 SHAFT MOTOR MN A-15 D-35 E-48 SHAFT 2 K-15 The motor is driven at 800 RPM. What is the output speed and direction of Shafts 1 and 2? b. J-42 8-40 C-20 F-12 G-72 SHAFT MOTOR MN A-15 D-35...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT