Homework Answers
Add Answer to:
5. Problem 3.54 (Textbook) (20 points) KNOWN: Diameter of electrical wire. Thickness and thermal conductivity of...
2-157 A long electrical resistance wire of radius r.-0.25 cm has a thermal conductivity kwire-15 W/m-K. Heat is gene...
2-157 A long electrical resistance wire of radius r.-0.25 cm has a thermal conductivity kwire-15 W/m-K. Heat is generated uniformly in the wire as a result of resistance heating at a constant rate of 0.5 W/cm3. The wire is covered with polyethylene insulation with a thickness of 0.25 cm and thermal conductivity of ks 0.4 W/m K. The outer surface of the insulation is subjected to free convection in air at 20°C and a convection heat transfer coefficient of 2...
A very long rod of 5-mm diameter and uniform thermal conductivity k = 25 W/m-K is subjected to a heat treatment process
A very long rod of 5-mm diameter and uniform thermal conductivity k = 25 W/m-K is subjected to a heat treatment process. The center, 30-mm-long portion of the rod within the induction heating coil experiences uniform volumetric heat generation of 7.5 x 106 W/m3. The unheated portions of the rod, which protrude from the heating coil on either side, experience convection with the ambient air at T∞ = 20 °C and h = 10 W/m2K. Assume that there is no convection...
A rod of diameter D = 25 mm and thermal conductivity of 60 W/m K protrudes from a furnace with a wall temperature of 200°C.
A rod of diameter D = 25 mm and thermal conductivity of 60 W/m K protrudes from a furnace with a wall temperature of 200°C. The rod is welded to the furnace wall and is used as a hangar for instrumentation cables. To avoid damaging the cables, the surface temperature of last 100 mm of the rod must be kept below 100°C. The ambient air temperature is 25°C and the convection coefficient is 15 W/m2K. (a) Write the finite-difference equation for...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY. A hollow aluminum sphere, with...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY.
A hollow aluminum sphere, with an electrical heater in the center, is used in tests to determine the thermal conductivity of insulating materials. The inner and outer radii of the sphere are 0.15 and 0.18 m, respectively, and testing is done under steady-state conditions with the inner surface of the aluminum maintained at 250°C. In a particular test, a spherical shell of insulation is cast on the outer surface...
Problem 2. A long thin alloy wire with a diameter of 0.2 mm is exposed to...
Problem 2. A long thin alloy wire with a diameter of 0.2 mm is exposed to ambient air at T, -25°C with a combined heat transfer coefficient h-10 W/m2.K (due to natural convection and radiation). An electric current10.15 A flows through the wire. The electrical resistance of the wire per unit length is R-162/m. (a) Draw a control volume to write down the energy balance equation. (b) Determine the steady-state temperature of the alloy wire, assuming that the solid wire...
Steady-State Conduction 3.25 Approximately 10° discrete electrical components can single integrated circuit (chip), with 30,000 W/m...
Steady-State Conduction 3.25 Approximately 10° discrete electrical components can single integrated circuit (chip), with 30,000 W/m 27 abe- be placed electrical heat dissipation The chip, which is very thin, is exposed to a tric liquid at its outer surface, with h, = 1000 W/m2 K and T inner surface. The thermal contact resistance between the chip and the board is 10 m K/W, and the board thickness and thermal conductivity are L and kp 1 W/m K, respectively. The other...
blem 4 (20 pts) A square chip that is 12.7mm on a side has a maximum allowable chip operating temperature -75°C. To dissipate heat produced in the chip, a 4 x 4 array of copper (k-400 W/m.K) pin fins...
blem 4 (20 pts) A square chip that is 12.7mm on a side has a maximum allowable chip operating temperature -75°C. To dissipate heat produced in the chip, a 4 x 4 array of copper (k-400 W/m.K) pin fins is proposed to be etallurgically joined to the outer surface of the chip. The convection coefficient is h-250 W/m'K and ambient air mperature isTo-20°C. The pin fin dimeter is D,-1.5mm and length is L,-16mm. Assuming steady-state uniform chip temperature Te-75°C and...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
summarizr the followung info and write them in your own words and break them into different...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
2-157 A long electrical resistance wire of radius r.-0.25 cm has a thermal conductivity kwire-15 W/m-K. Heat is generated uniformly in the wire as a result of resistance heating at a constant rate of 0.5 W/cm3. The wire is covered with polyethylene insulation with a thickness of 0.25 cm and thermal conductivity of ks 0.4 W/m K. The outer surface of the insulation is subjected to free convection in air at 20°C and a convection heat transfer coefficient of 2...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY.
A hollow aluminum sphere, with an electrical heater in the center, is used in tests to determine the thermal conductivity of insulating materials. The inner and outer radii of the sphere are 0.15 and 0.18 m, respectively, and testing is done under steady-state conditions with the inner surface of the aluminum maintained at 250°C. In a particular test, a spherical shell of insulation is cast on the outer surface...
Problem 2. A long thin alloy wire with a diameter of 0.2 mm is exposed to ambient air at T, -25°C with a combined heat transfer coefficient h-10 W/m2.K (due to natural convection and radiation). An electric current10.15 A flows through the wire. The electrical resistance of the wire per unit length is R-162/m. (a) Draw a control volume to write down the energy balance equation. (b) Determine the steady-state temperature of the alloy wire, assuming that the solid wire...
Steady-State Conduction 3.25 Approximately 10° discrete electrical components can single integrated circuit (chip), with 30,000 W/m 27 abe- be placed electrical heat dissipation The chip, which is very thin, is exposed to a tric liquid at its outer surface, with h, = 1000 W/m2 K and T inner surface. The thermal contact resistance between the chip and the board is 10 m K/W, and the board thickness and thermal conductivity are L and kp 1 W/m K, respectively. The other...
blem 4 (20 pts) A square chip that is 12.7mm on a side has a maximum allowable chip operating temperature -75°C. To dissipate heat produced in the chip, a 4 x 4 array of copper (k-400 W/m.K) pin fins is proposed to be etallurgically joined to the outer surface of the chip. The convection coefficient is h-250 W/m'K and ambient air mperature isTo-20°C. The pin fin dimeter is D,-1.5mm and length is L,-16mm. Assuming steady-state uniform chip temperature Te-75°C and...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
Your system is rejecting the question am asking which is
preceded by a case study. It...
asked 1 minute from now -
A member of the volleyball team spikes the ball. During this
process, she changes the velocity...
asked 2 minutes ago -
Are adult gamers less likely to use a gaming console (Xbox,
PlayStation, Wii, etc...) than teen...
asked 55 minutes ago -
The University of
Texas recently reported that 43% of college students aged 18-24
would spend their...
asked 1 hour ago -
The length of stay at a specific emergency department in
Phoenix, Arizona, in 2009 had a...
asked 22 minutes ago -
. Please give the mechanism for this type of problem. Step by
Step
The toxin that...
asked 25 minutes ago -
If you have a 1M stock solution and you want to dilute 1 :10
with water,...
asked 27 minutes ago -
In a load instruction, the effective address is obtained by
A) Retriving the address from a...
asked 27 minutes ago -
Use the following information to answer this question.
Windswept, Inc. 2017 Income Statement ($ in millions)...
asked 28 minutes ago -
A mutual fund salesperson has arranged to call on four people
tomorrow. Based on past experience...
asked 1 hour ago -
Let the RV Y has the pdf
f ( y ) = 6 y ( 1...
asked 1 hour ago -
Question 12
Where should a copy of a private key should be placed so it is...
asked 31 minutes ago