3. IN THE DIGRAM EVERY DEVICE HAS WRITTEN THEIR CORESPONDING IP ADDRESS.
4. lan cable used in same type of device is crossover cable. ex: b/w 2 pc , 2 server, 2 switches etc
lan cable used in diffrent type of device : coaxial cable ex: between pc and server etc.
5.
i. Setting up the access point as an access point - The Access Point mode is the default setting of most Linksys wireless access points. It allows you to extend the range of an existing wireless signal by connecting the access point to a wireless router via Ethernet connection. It also allows you to create another wireless network with a different SSID and channel on the same local network using the same LAN IP segment.
ii. Setting up the access point as a wireless repeater - The Wireless Repeater mode allows this device to act as a wireless repeater. A wireless repeater can extend the range of your wireless signal without sacrificing the transmit rate.
To learn how to set up the Linksys access point as an access point, follow the instructions provided below:
Setting up the access point as an access point
This setup will work even if you have a wired or wireless
router. Simply connect the access point to one of the ports of your
existing wired/wireless router then configure the access point’s
wireless settings.
Step 1:
Open the access point’s web-based setup page by entering the
default IP Address “192.168.1.245” on the Address bar then press
[Enter]. If a new window prompts for credentials,
leave the User name blank and enter “admin” as
your Password then click
OK.
Step 2:
On the web-based setup page, click on
Wireless.
Step 3:
Enter the Network Name (SSID).
The SSID Broadcast should be set to
Enabled so that wireless devices will be able to
detect the wireless network of your Linksys access point.
Step 4:
Click Wireless Security and select your desired
Security Mode.
6.
It starts with a basic multi-user operating system. Usually it has local storage for the operating system, but not always - it is possible to have remote storage and network boot for the system.
What gets added to it depends on who provides it. Generally it will include
But all of this is layered on the basic operating system.
we have for lineand need to connection to gether 3 Do the following: LANI: consist of...
Consider the topology shown below with following requirements Three subnets A, B, C, should have enough addresses, starting from 192.100.10.0 to support 500 interfaces, 200 interfaces, and 100 interfaces, respectively. Each of subnets, D, E, and F has 32 interfaces. (not required for address assignment.) The IP addresses for three subnets should be assigned continuously, with spacing of power-2, that means, 250 will be rounded to 256, and so on. For each subnet, the assignment should take the form a.b.c.d/x...
urgent please if you can not give answer in 1 hour kindly do not give then because i have quiz.thanks OnalA Student No: Student Name: Question 5: There are three IP kinds in comm on use, A, B, and C. Now what is the kind of IP address 192.168.145.123 (subnet mask is 255.255.225.240)? And what is it's Net ID, Subnet number and Host number? How many Host numbers are in one subnet? (20 marks) OnalA Student No: Student Name: Question...
Design a Logical Topology with the following constraints: Material Constraints: 2x 24-Port, Layer 3 Network Switches 1x Edge Router (connected out to the local LAN, the external RV215W LAN, and the WAN - 3 total connections) 2x Wireless Access Points 1x Cisco RV215W (connected to the edge router to allow LAN communication from another building) 30 total network devices (these will determine your total subnets/VLANs and subnet scopes): 10 VoIP phones 4 Executive computers 2 Administration computers 2 Finance computers...
A/ Given the following IP address from the Class B address range using the default subnet mask: 100.110.0.0. Your network plan requires no more than 64 hosts on a subnet. When you configure the IP address in Cisco IOS software, which value should you use as the subnet mask? 255.255.0.0 255.255.128.0 255.255.255.128 255.255.255.252 B/ Identify how many valid host addresses can you have on 192.168.27.32 network with a subnet mask of 255.255.255.240. (2^4) - 2 (2^3) – 2 (2^2)...
7. Write down the last network address for the network classes listed below: (do not use any reserved address) Class C Class B Class A Tabie 3 3 marksy 8. The following host IP addresses all belong to IP4 subnetted networks. Using the information provided (IP address and network prefix length), fill in the table with the Subnetwork Address of the subnet to which the host belongs, the subnet mask and the number of host each subnetwork can accommodate. Host...
1. Which 802.11 standard has the best performing parameters in terms of data rate, range, channel separation issues and interoperability? 802.11n 802.11b 802.11g 802.11a 2. WPA2 uses IEEE 802.X with the Extensible Authentication Protocol (EAP) to perform mutual authentication, either via a _________ server or by means of a changing key generated on the basis of a shared secret pass-phrase. AES RADIUS WEP Common 3. At the MAC level, 802.11 LANs involve the use of ______ for medium access control....
Scenaric im runs a small consulting firm, Soylent Co, with 30 employees spread between accounts, human resources, administration, and engineering. Jim's son, Tony, knows a bit about computers and so Jim has asked him to upgrade the company network. You went to high school with Tony. You receive a panicked phone call from Tony telling you that he has spent the last two days trying to find why his father's newly upgraded network is having significant stability problems. You've agreed...
1. TCP has which of the following characteristics. Choose all true statements. three-way hand shake none of the above regulated send rate connection state at the server 2. Consider a subnet with prefix 128.119.40.128/26. Given an example of one IP address (of form xxx.xxx.xxx.xxx) that can be assigned to this network. Suppose an ISP owns the block of addresses of the form 128.119.40.64/26. Suppose it wants to create four subnets from this block, with each block having the same number...
Question 1 (a) Describe the five IP addressing classes. Provide an example for each of classes in binary and dotted-decimal representation. (b) Show the conversion of each of the addresses. (c) Describe the function of the subnet address for each of the classes and how does it work. [20 Marks] Question 2 (a) Define message switching, circuit switching and packet switching. Draw a diagram for each method to show the difference between them. (b) Identify the samples of network environment...
check my answers for Networking I came up with these answers, can check my answers Question 1: General What data rate is needed to transmit an uncompressed 4" x 6" photograph every second with a resolution of 1200 dots per inch and 24 bits per dot (pixel)? 691,200 kb/s 28.8 kb/s 8.29 Mb/s 829 Mb/s Question 2: Layering "Layering" is commonly used in computer networks because (check all that apply): -It forces all network software to be written in ‘C’....