(1 point) Problem 3 For the circuit given below. R1-1 ?? and R2-14152. Calculate the voltage...
I need help to find the values!
gures below (a-d), determine the values for R1, R2, voltage or type of op-amp based on the information listed. You may ors with an open circuit, short circuit, or values 1kn SRS1Mn. gain, voltage, a) 76 k2 Type: Non-Inverting Vout max R1 (based on Voutmas) 0.3V Type: Inverting, Av =-100 V/V Vin- b) R1 12V R1 12V Type: Buffer Vout- R1 =- c) +10 V R1 ーVout -10 V Type: Av- IV R2...
3. In the circuit below. R1 = 10k, R2 = 20k and C = 0,1,1F. At t = 0, a step function of 10 V magnitude is applied to the input. Find V(t) at the output and sketch it. Your sketch should be quantitatively correct, that is, it should have labeled V and t axes. Strongly suggested: solve by first finding the Thévenin equivalent of the source voltage and resistor network. Input (problem 3) R1 10V IN R2 C1 OUT...
Q3. In the circuit as shown below, given that R1 = 4 Ω, R2-4 Ω, L 2 H, and C = 0.5 F, where vs(t) is given by the waveform displayed in the same figure 1 V (a) Determine the s-domain current I(so) at so-0.05 jo.07 (rad/s): IL(So)- Submit Answer Tries 0/3 (b) Determine the t-domain current i(to) at to 4.5 (s): Submit Answer Tries 0/8 Q4. Determine the output voltage in the circuit as shown below, given that Vs-35*u(t)...
Problem 2. For the following circuit: R1 R2 Va OPAMP Vout OUT 0 (a) What is formula for Ay? (b) what islout if R1 = 1M? and R2 AM2? (c) What is Vout if R1 = 8M2 and R2 = 1 kΩ? (d) What is Vout if R1-5k and R2 100k2? (e) what is V, if R1-2kS2 and R2-2kΩ? (f) Given your answer to (e), does this circuit have a virtual ground?
Problem 3: Determine explicitly the voltage across R3 in the circuit below R2 R1 R3 R4 (Hint: R2 and R3 are in parallel with R1... this combination is in series with R4. The total resistance can give you the total voltage drop AND then you can just analyze as a voltage divider.)
3-F) b. Vout = 0.99 Vin
3-E) For the following circuit, with Ri 18 k2, R2 15 k(2, R6 = 40 kQ, V,-10 V, and V,-7 V, find: 22 k2, R 30 k2, R4 20 kQ, Rs- a) the current through Ri, R3, & R6 b) the voltage across R2, R4, & Rs Rs V, 3-F) For the following circuit, what is Vout in terms of Vin for each case? a) R1-100 ?, R2-1 k(2, and R3 = 1.0 M(2...
C.la For the circuit of Figure 1, choose values for resistors R1, R2, and R3(all resistances must be greater than one Kilo ohm). Given that the voltage source Vs1 = 8V and Vs2 = 10V determine the output voltage Vout. C.1b For the same resistor values Ri, R2, and Rs you chose in part C.la Given that the voltage source Vsi = 8V and Vs2 = 10V, use Figure 2(a) to determine the output voltage Vout/ and Figure 2(b) to determine the output voltage Vout2. Discussion:...
2. In the circuit below, R1 = 10k, R2 : magnitude is applied to the input. Find V(t) at the output and sketch it. Your sketch should be quantitatively correct, that is, it should have labeled V and t axes. Strongly suggested: solve by first finding the Thévenin equivalent of the source voltage and resistor network. 20k and C = 0.1µF. At t = 0, a step function of 10 V Input (problem 3) R, 10V- IN R2 C, OUT...
1. Find the expression for the output voltage Vou for the circuit shown below in terms of the resistors Ri, R, R and Rs and the input voltages Vi. V2 and V Calculate Vout when R.-R: = R.-1? and R.-10kfand V, = 4nnV, V,-5mV and V,-6m1V. N3. 2. Find the expression for the output voltage in the circuit shown below and calculate the output voltage Vou where R-R-2.2 k2 and R R-10kQ. V-4 V and V the output voltage when...
For the circuit shown below, design the values of R1 and R2 that will cause Vout-6 Vif VIv-9 V. If the resistors you chose have a tolerance of 1 %, what is the maximum and minimum values of Vout? Design R3 so that the LED will be properly lit, if IF=10 mA, VF-3 V and Vout-6 V Design equations from the data sheet: VOUT-1.25%(1+R2 R1) U1 OUT ININLT OUT R3 R1 V1 (R3) R1) ADJ LT317A D1 IN) R2 (R2)...