2. ( 10 points: S points each) Suppose we have a hypothetical processor, of which each...
Suppose we have a hypothetical processor, of which each register has only five bits. r0 = 0b11101 and r1 = 0b10110. What are the N,Z,C, and V flags of the following instructions? Assume initially N = 0, Z = 0, C = 1, V = 0, and these instructions are executed independently (1) ADDS r3, r0, r1 (2) SUBS r3, r0, r1 (3) EOR r3, r0, r1 (4) ANDS r3, r1, r1, LSL #3
Ox00000000. Initially N-Z=C=V=0. Find the new values ofr3, N, Z, C, and V running each following instructions 5. Suppose r0 0XFFFFFFFF, rl = 0x00000001 and r2 independently (i.e. same starting values for each case). Not graded: check results with TIVA. ADDS r3, r0, r2 а. b. SUBS r3, r1, r0 ; note: not the LSLS instruction r3, r0, #1 LSL с.
Suppose we have a 32-bit MIPS processor, which includes a 2-way set associative data cache with capacity 16384 bytes, 16 bytes block, and a least recently used (LRU) replacement policy. Assume that the cache is empty (all valid bits are 0) before the following code is executed. lw $t1, 0x1040($0) lw $t2, 0x2044($0) lw $t3, 0x3048($0) lw $t4, 0x1044($0) lw $t5, 0x504c($0) lw $t6, 0x3040($0) For each of the six assembly instructions above, state i) the set field value for...
A C program has been compiled into the Atmel AVR assembly
language. The following instruction, which is located at address
0x002A, is executed:
i.) What is the binary value contained in the instruction
register (IR) when the instruction is executed?
ii.) What is the hexadecimal value of the program counter (PC)
when the instruction is executed?
iii.) If register r1 = 0x40 and register r2 = 0x02 prior to
executing the instruction, what are the contents of r1 and r2...
Computer architecture help:
(60 points) The following instructions are executed on the 5-stage MIPS pipelined datapath. add r5,r2, r1 lw r3, 4(r5) lw r2, 0(r2) or r3, r5, r3 sw r3, 0(r5) (a) (20 points) List the data hazards in the above code. For each data hazard identified, clearly mark the source and the destination. For example you can say, there is a data hazard from instruction X to instruction Y on register Z. (b) (20 points) Assume there is...
5. (35 points) (a) (10 points) Calculate the equivalent resistance of the diagrammed network of resistors. (b) (10 points) Calculate the current through each resistor. (c) (10 points) Calculate the power dissipated by each resistor. (d) (5 points) Show that the power supplied by the battery equals the sum of the power dissipated by the resistors. (e) (5 extra credit points) What is Vbc = Vc - V.? (f) (5 extra credit points) What value of R2 will make Vbc...
12 po Iw add Question 11 The dassic five-stage pipeline MIPS architecture is used to execute the code fragments in this problem. Assume the followings: • The architecture fully supports forwarding • Register write is done in the first half of the clock cycles register read is performed in the second half of the clock cyde. Branches are resolved in the third stage of the pipeline and the architecture does not utilize any branch prediction mechanism Register R4 is initially...
Question 3. (10 points) Four resistors are connected as shown in Figure 28.9a Find the equivalent resistance between a and c. R1-16 and R4-12 Ω R2-13 R3-4 (a) (b) What is the current in each resistor if a potential difference of 0.64 V is maintained between a and c. Calculate the current in each resistor I (for Ri resistor)- I (for R2 resistor)- I (for R3 resistor) I (for R4 resistor)- Which resistor uses more power, R or R4? Which...
Motes Ask Your Teacher 10. 0/12 points| Previous Ansiwers PSEB 2B.AF.a4 Active Figure 28.4 Resistors Connected in Series The animation below shows a circuit diagram for two resistors connected in series acrass a battery Instructions Use the sliders to adjust the resistances and battery voltage and observe the effect on the current and voltages across each resistor. Explore In the animation, the two resistors are connected directly to the battery, so they both share a portion of the battery voltage...
can you show me how you get each one or fill the table?
Given the following memory and register values as shown in Tables 1& 2 below: Determine the values of the A, B, X, Y, CCR & SP registers in Table 1 as the program is executed Show new values of memory content in Table 2 if the memory location content is affected. - NOTE: This is a continues program where instruction results affect the instruction that follows Leave...