Draw the shear and moment diagram for the loaded structure shown below. Replace the magnitude of...
Draw completely the shear (V) and Moment (M) diagram of the following beam loaded as shown fer Draw completely the shear (V) and Moment (M) diagram of the following beam loaded as shown Prob 02 100 KN 80 KN 0 KNm 20 KN/m 2 m 2m 2 m 6 m R 2 R 1
The beam is loaded as shown in the diagram below. The beam is uniformly loaded at 3 kN/m for the length of 4 m from B. The beam also has two point loads, 4 KN at 2 m from A and 3 KN at 3 m from B. 2 KN 3 KN 3KN/m A 2 m 2 m 11 m 3 m Fig. Q2 Draw a shear force and bending moment diagram. Also determine the location of maximum bending moment...
Help with the shear and moment diagram SHEAR AND MOMENT DIAGRAM: Draw diagram (20pts.) and label the parts of the load diagram and shear and moment 23. For the given frame draw the shear and moment diagram of each member 22 kN/m 5 m Hinge 5 m 110kN 1475 FOR MEMBER AC FOR MEMBER CE 27 FOR MEMBER EG /47s llD Page d of 4
Problem 1 Beams (a) - (g) shown below are simply supported and loaded at their ends by two concentrated moments of magnitude PL/10. In addition to the moments, beams (a) – (d) are subject to a uniformly distributed load of magnitude 2P/L, and beams (e) – (h) are subject to a concentrated load at midspan of magnitude P (note the directions of the loads). All beams have length L. Draw the shear and moment diagram for all cases shown. (b)....
For the beam shown in Fig. 9.3, draw the shear force and bending moment diagrams. Use the area method that relies on the relationships between loading and shear force and between shear force and bending moment. Indicate the slope of the shear force diagram at locations A, B, C, and D using the load information in Fig. 9.3. Indicate the slope of the bending moment diagram at the same four locations using information from the shear force diagram. | 6...
Problem 2: A beam is loaded and supported as shown below. Please draw the complete shear and bending moment diagrams 3 kN 4 kN/m 6kN С 3 kNm DI A В. -1.5 m-*-1 m 6 kN m -2 m -1.5 m 11 KN OKN 18 kN 12
Draw the Bending moment and the Shear force diagram for the frame structure shown below. Check your answers at the key points to see if your calculations are right.
Analyse the structure shown and determine the following: a) Reactions (8 marks) b) Shear force diagram (4 marks) c) Axial force diagram(4 marks) d) Bending moment diagram (4 marks) Question 1 (20 marks) Analyse the structure shown and determine the following: a) Reactions (8 marks) b) Shear force diagram (4 marks) c) Axial force diagram(4 marks) d) Bending moment diagram (4 marks) 25 kN/m 2C 3 m D 4 m 6 m Show your computations in the solution book then...
A beam is shown in the figure below: Part A: Draw a shear Diagram for the beam: Part B: Draw the moment diagram for the beam: 20 kN 20 kN/m -2 m V(kN 40 20 x(m) -20 -40 -60 5 )d 0 0 0 0 00000 m5 4 3 2 1 20 kN 20 kN/m -2 m V(kN 40 20 x(m) -20 -40 -60 5 )d 0 0 0 0 00000 m5 4 3 2 1
Problem 1 The rigid structure shown in the figure below is loaded with a concentric couple applied at H of 75 kNm and a concentric horizontal force of 40 kN. A distributed load spans from point D through E with minimum amplitude of 10 kN/m and a maximum of 30 kN/m, respectively. The structure is externally supported by a roller at A, the cable BC and a pin at G. Please do the following: 1. Draw a neat Free Body...