valence shell electron configuration of N is 2s2 2p3.
and electron configuration of C is 2s2 sp2.
so from electron configuration of N, we can see that 2p orbital is half filled but in case of C, 2p have 2 electrons that is less than half filled.
Hence electron configuration of N is more stable than C.
so electron affinity of N is less than that of C.
C and N is the answer.
Correct Part B-In the second period (and at the same positions in the third and fourth...
Chapter o Problem 6.34 Part A Consider the volume shown in (Figure 1) Suppose that a 1.8 m,b Locate the centroid ž of the volume Express your answer to three sig Submit Request Answer Figure 1 of 1 > Provide Feedback
Find the angle Part A B 0.11 T and F 3.6x10-13 N. What is the electric field strength at the position of the electron in (Figure 1)? Assume that Express your answer with the appropriate units. E- 1.9x10 Correct Part B What is the electric field direction at the position of the electron? , measured clockwise trom the positive z axis in zy plane Submit gure 1 of 1 Incorrect: One attempt remaining: Try Again Provide Feedback 30° Moving out...
10 P 13.64 く 100f 12:>) Review Part A Select the correct dc imperfections of real op amps Check all that apply high output impedance offset voltage bias current limited bandwidth D offset current Submit st Answer Part B Complete previous part(s) Provide Feedback Next>
Part C If cable AB is subjected to a tension of 750 N, determine the magnitude of the vertical force F. Figure < 1 of 1 > Express your answer to three significant figures and include the appropriate units. R 2 ? 19 Å F= 1135.715 O kN 2 m Submit Previous Answers Request Answer 1.5 m X Incorrect; Try Again; 4 attempts remaining 6 m 3m7 B Provide Feedback
Part B Find the spring constant k' of the three-spring system. Express your answer in terms of ki, k2, and k3. Figure < 2 of 2 > PO AQ * * o a? k' = Submit Previous Answers Request Answer ki kz kz WWW -W -F_ Spring 1 Spring 2 Spring 3 X Incorrect; Try Again; 7 attempts remaining Your answer does not have dimensions of a spring constant. If you are trying to generalize kik2/(ki + k2), you need...
For= 334 N Previous Answers Correct Part B Determine the magnitude of the component of F-600 N acting perpendicularlo segment DE of the pipe assembly Express your answer with the appropriate units. re 1 of 1 HA + O ? F. - 443 N Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining Provide Feedback
Part A Two point charges are placed on the z axis as follows: Charge q-+4.20 nC is located atz 0.225 m and charge 92--5.65 nC is at-0.400 m. What is the magnitude of the net force exerted by these two charges on a third point charge 30.610 nC placed at the origin? Express your answer in newtons to three significant figures. Font Submit Request Answer Part B What is the direction of the net force exerted by these two charges...
Please help! 1. Write linear electron configurations for the following: a. Co__225 2352 345 2. b. Sn°227.3.230645 201104ple 5s 5 d'° Spal c. Rb_s"25k 20133239645230104.455 d. Sg. 23,045 2.d4 155440445ples? 5d05f14cplo 752 lods e. As3-Aras 3d 4p3 2.Write the orbital box diagram for arsenic and sulfur As (Arsenic) S (sulfur IN N N 3p D3 35 N N TN2p Pe 25 Nas 3. Write the inert-gas core diagrams for: a. Hg+2 x 145'4 5d tesố b. S-2 (Ne]352304 c. Eu...
Problem 5.58 < 18 of 18 > a Review Part A The turbine develops 150 kW of power, which is transmitted to the gears such that both C and I receive an equal amount. The rotation of the 100-CELELL-diameter A-36 steel shaft is w = 800 rev/min. The journal bearing at allows the shaft to turn freely about its axis. The shear modulus of elasticity for the A-36 steel is 75 GPa (Figure 1) Determine the absolute maximum shear stress...
please answer part A and B. In (Figure 1), y = 10.1 ksi. Figure < 1 of 1 20 ksi 10 ksi P 1 o Tyn hart Part A Determine the principal stresses. Specify the orientation of the element. Express your answers, separated by commas, to three significant figures. 110 AED 11 vec ? 01 =, 02 =, Opt= ksi, ksi, (clockwise) Submit Request Answer Part B Determine the maximum in-plane shear stress and average normal stress. Specify the orientation...