6.4. For the beam loaded as shown in Figure 6.4, A is a pin and B...
The beam AC is supported by a smooth pin at A and a roller at B
as shown in the figure below.
a. Sketch the free-body diagram of the beam and use it to
determine the support reaction components at A and B.
b. Draw the shear and moment diagrams for the beam.
6. The beam AC is supported by a smooth pin at A and a roller at B as shown in the figure below. 6 kN 12 kN/m...
Problem 1 The rigid structure shown in the figure below is loaded with a concentric couple applied at H of 75 kNm and a concentric horizontal force of 40 kN. A distributed load spans from point D through E with minimum amplitude of 10 kN/m and a maximum of 30 kN/m, respectively. The structure is externally supported by a roller at A, the cable BC and a pin at G. Please do the following: 1. Draw a neat Free Body...
The beam shown in figure below is connected to a pin at point A and rests on a roller at point B. Consider the weight of the beam, draw a free-body diagram of the beam? 17. 6KN 10KN 75"
The beam shown in figure below is connected to a pin at point A and rests on a roller at point B. Consider the weight of the beam, draw a free-body diagram of the beam? 17. 6KN 10KN 75"
A loaded beam with a pin support at B and a roller support at C
is shown in Figure 1. The applied loads on the beam are: an
anti-clockwise point moment at A, a variably distributed load
between B and C, and a clockwise point moment at D.
A loaded beam with a pin support at B and a roller support at C is shown in Figure 1. The applied loads on the beam are: an anti-clockwise point moment at...
A loaded beam with a pin support at B and a rller support at C is shown in Figure 1. The applied loads on the beam are: an anti-clockwise point moment at A, a variably distributed load between B and C, and a clockwise point moment at D g kN/m f kNm h kN m A C 4 m 2 m 2 m Figure 1 The magnitude of the anti-clockwise point moment f in units of kN'm can be found...
SECTION A Question A1. A beam is subjected to a 500kN force and a 600kNm couple as shown in Figure QA1. a) Draw the free body diagram of the beam. (5 marks) b) Calculate the reactions at A and B. [15 marks] 500 KN 600 kNm B 5 m 5 m 5 m X Figure QA1 400455 Page 2 of 5
QUESTION 2 Beam ABCD is 8 m in length and is pin-supported at A and roller-supported at C as shown in Figure Q2. A counter-clockwise concentrated moment acts about the support A. A uniformly-distributed load acts on span BC and a vertical concentrated load acts at the free end D a) Determine the reactions at supports A and C. 4 marks) b) Obtain the shear force and the bending moment functions (in terms of x) for each segment along the...
Figure Q1(b) shows a beam AD which is loaded with the force F.
The coefficient of static friction at the top and bottom surfaces
of the wedge are ???=0.25 and ???=0.35, respectively. Neglect the
weight, size of the wedge and the thickness of the beam.
Considering the value of F from the Table Q1(b) attached, answer
the following;
(i) Draw the free body diagram of the given problem with all forces
and support reactions.
(2 marks)
(ii) Determine the horizontal...
1 Review - Part B Draw the moment diagrams for the beam shown in (Figure 1) using the method of superposition. Consider the beam to be cantilevered from the support at (BV). Follow the sign convention. Draw the moment diagram for the force shown in the figure below. Click on "add vertical line off" to add vertical lines. Then click on "add segment" button to add functions between the lines. Note 1 - Make sure you place only one vertical...
Q2(c) Figure Q1(c) shows a simply supported beam ABCD loaded as shown. The beam is pin-supported at D, while point B is roller-supported. Determine the support reactions. b) For span BC (2<x< 4) write down the x-dependent equation for moment. x should be measured from cnd A. Plot the shear force diagram and the bending moment diagram for the beam. Show all important values of the diagrams. d) Plot the deflected shape of the beam. c) 50KN 40kN/m 25kNm 20kN/m...