possible to explain step by step:(
possible to explain step by step:( 1. Find an expression for VouT as a function of...
Find the output voltage Vo as an expression in terms of the input sources Vi, v2, v3, and the resistance R in the following op-amp circuit. 3. Ri Vy R: 4. In the following two stage op-amp circuit, find the output voltage Vo as an expression in terms of the input voltages v1, v2 and resistor values R1, R2, R3, and R4. R2 R ウー+
is it ok to use R1=4.7Kohms and C1=330pf? And I want to know how to calculate the R2, Rsrc, and C2 tage 2:Baseband Filter The filter schematic is shown in Fig. 3. Select resistor Rj and capacitor C1 so that the cut-off frequency of the filter response is below 100kHz. The input network formed by resistors Rsrc, R2 and capacitor C2 also has a low pass response that should attenuate the input Vsrc seen at the top of capacitor C2...
Need b and c [Q-1, 12 Marks] Answer the following briefly: (Imprecise answers will get zero marks) 1· (a) Check if the dominant poles concept is applicable (show your pole-zero skctch) to the system 630 G(s) (s2 16s 63) (s1.4s 2) and if it is, then i. Obtain the equivalent second order system transfer function i. Calculate the time to peak, overshoot and settling time iii. Sketch the second order system step response with the calculated parameters marked in the...
Q1. You are given a 12 V DC power supply. You are expected to develop a voltage divider to achieve a voltage of nominal 5V value using a pair of resistors from the E 12 range, with the restrition that you are not expected to draw a current of more than 1 mA from the 12 V DC supply i. Develop a simple circuit showing the possible values for each resistor pair, and the range of the DC output possible...
thanks Laboratory 1: operation amplifier characteristics A. Objectives: 1. To study the basic characteristics of an operational amplifier 2. To study the bias circuit of an operational amplifier B. Apparatus: 1. DC Power supply 2. Experimental board and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Multimeter...
Device A: mean 116, standard deviation 0.5 mmH Device B: mean 111, standard deviation 1.8 mmHo te the better device in terms of () precision error and (ii) bias error, and explain why Question 2: Conditioning Circuits resist are typically accounted for or compensated for in practice. B. i. Derive the complex transfer function H(o) for each of the two circuits shown in Figure 1. o is defined as frequency in rad/s. art from finite open-loop gain, finite input resistance...
d. none of the above The following questions pertain to the circuits shown below. 3mA ? 30 MO 15 M2 бmA In an amplifier design, your company has a non-ideal current source. The amplifier acts like a resister of 15MQ but can only take 3mA as input or it will overheat and cease function. It was discovered in testing that the above schematic delivered 4mA to the amplifier and most of the amps burned out. Over 1000 of these amps...
1. RL Circuits For the circuit in Figure 1, find the inductor voltage vit) if a) v(t) is the step function: 0 Vfor t<0 and 10 V for t>0. What is the time constant in this case? b) vs(t) 15 cos(100 t). You may use either the direct time-domain method, or use (complex) phasor method. 52 102 5mH L(t) Figure 1 2. Impedance You are given six black boxes, labelled "1" to ", each with two terminals. You are told...
Question 1 In the diagram of Superheterodne AM receiver shown below explain the function of each block. (a) 15 marks Antenna Speaker Audio and power amplifiers RF IF Mixer Detector Mi amplifier amplifier AGC --_Local Gang tuned oscillator (b) For a 4-bit DAC, calculate the output voltage for an input code word 1010 if a [10 marks] logic 1 is 10V and a logic 0 is 0V, and R = RFI kΩ Total: 25 marks] Question 2 (a) Explain the...
Infix Expression Evaluator For this project, write a C program that will evaluate an infix expression. The algorithm REQUIRED for this program will use two stacks, an operator stack and a value stack. Both stacks MUST be implemented using a linked list. For this program, you are to write functions for the linked list stacks with the following names: int isEmpty (stack); void push (stack, data); data top (stack); void pop (stack); // return TRUE if the stack has no...