Please answer question 4 thank you. Results from problem 3 are shown above
Reinforced Concrete
Please answer question 4 thank you. Results from problem 3 are shown above Reinforced Concrete 3....
Please answer question 3 parts a,b,c thank you Reinforced Concrete HW 3. (40 pts) Analyze the following statically determinate frame by hand and clearly draw the shear force, axial force, and bending moment diagrams indicating relevant (maximum and minimum) values for each of the following load cases: a) Uniform dead load (qo) applied on the beam – must add beam self-weight (concrete) to this value. b) Uniform live load (q) applied on the beam. c) Horizontal wind force (H). H=...
3. (40 pts) Analyze the following statically determinate frame by hand and clearly draw the shear force, axial force, and bending moment diagrams indicating relevant (maximum and minimum) values for each of the following load cases: a) Uniform dead load (q) applied on the beam must add beam self-weight (concrete) to this value b) Uniform live load (qu) applied on the beam. c) Horizontal wind force (H H=12kip 12 x 20 gp-1.4 kip/ft -2.0 kip/ft 14 ft 12" x 12...
Please answer question 1 thank you Reinforced Concrete HW 18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
Please answer question 1 thank you Reinforced Concrete HW 18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
please solve completely and correctly, I will give thumbs up! Force Method. The reinforced concrete beam as shown in “Figure 1" has a constant cross sectional dimension of 10" x 12" (b x h). The unit weight of the concrete is 150 lb/ft3. The 28-day concrete compressive strength of the beam is = 4000 psi. Use the classical force method to analyze the indeterminate beam under the applied dead load only. Assume the following values of span length: L1 =...
Hello, I am having a difficult time with this question. Can you help, please? roblem IV A preliminary design results in a W12 x 96 for Columns BE and HK in the structure shown below. Frames ADGL, BEHK, and CFIJ are moment frames. Dead load is 110 psf and live load is 95 psf The results obtained from an approximate first order analysis for column BE are also shown below teral Deflection (A) al 26.5 kip 23 kip 10 kip...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Usea concrete compressive...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Use a concrete...
Please answer question 3. The dimensions are given in problem 1 thank you Reinforced Concrete df Assigned: 20 February 2018 Due: 01 March 2018 1. For the rectangular cross section shown compute the nominal (M,) and design flexural strength (OM.) using the different reinforcement ratios corresponding to a net tensile strain of 0.002, 0.0025, 0.0030, 0.0035, 0.004, 0.0045, 0.005. Use f, = 60,000 psi and f', = 4,000 psi. Using these data points, plot M, and OM, as a function...
I need an answer for question 3 with steps please. Thank you half the load over Problem 2 eben The beam shown below with a uniformly span, with w3 kip/th and L 20 t shear force and bending moment diagrams for the beam using the standard sign convention Draw clear, complete and accurate Free Body Diagrams Problem 3: Siven: The beam below with a uniformly distributed load in the center span and concentrated moments at each end of the cantilever...