G is 11.2*10^6 psi A shaft of length 2 m has the hollow cross section shown...

Question

Question

A shaft of length 2 m has the hollow cross section shown below (distances of the centerline of the wall shown). The shaft is

G is 11.2*10^6 psi

Answer 1

Answer #1

Answer:

Solution Griven 1-2m, TF10 kNm Az Ttamm Constant) G=79.3GPG A = 2 A, = 11 (30)>= 2826 mm2 A2 = 30 X 60 = 1800 mm? A3 = 5(60 t

6) Angle of Twis e = 1 g de (Stasepa Asu] OLAZG t . 2(104) 0.35164 4 (6-126x60*3)*x 793 x109 ( 2 x16 0-0.295

Answer 2

Similar Homework Help Questions

(2) For the shown hollow steel shaft, it is required 1.00 m to determine the maximum...

(2) For the shown hollow steel shaft, it is required 1.00 m to determine the maximum torque T that can be resisted by the shaft so that: a) The maximum shear stress does not exceed 60 MPа. т b) The maximum angle of twist does not exceed 3° Given: The shear modulus, G = 70 GPa 30 mm 25 mm
160 mm 10 mm A hollow cylindrical steel shaft is 1.5 m long and has inner...

160 mm 10 mm A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. The allowable shearing stress is 120 MPa with a modulus of rigidity (shear modulus) G-77 GPa, assuming fully elastic deformation. (a) What is the largest torque that can be applied to the shaft? (5 points) (b) What is the corresponding minimum value of the shearing stress in the shaft? (5 points) (c) What are...
Sup 3.2 A hollow aluminum allow [G 3.8 x 10* psi) shaft having a length of...

Sup 3.2 A hollow aluminum allow [G 3.8 x 10* psi) shaft having a length of 12 ft., an outside diameter of 4.50 in., and a wall thickness of 0.50 in. rotates at 3 Hz. The allowable shear stress is 6 ksi, and the allowable angle of twist is 5°. What horsepower may the shaft transmit?

P.4 A 750-N. m torque is applied to a hollow shaft having the cross section shown...

P.4 A 750-N. m torque is applied to a hollow shaft having the cross section shown and a uniform 6-mm wall thickness. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. 30 mm 60 mm 30 mm
please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity...

please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
The solid steel shafts (G=77GPa) are surrounded by the gears shown. A torque T=340 N.m is...

The solid steel shafts (G=77GPa) are surrounded by the gears shown. A torque T=340 N.m is applied at point A, determine: 1. The shear stress in shaft EC; 2. The angle through which end A rotates. The solid steel shafts (G-77GPa) are sITounded by the gears shown. A torque T 340 N.m is applied at point A, determine: 1. The shear stress in shaft EC 2. The angle through which end A rotates. 30 mm 200 mm 400 mm 60...

The power loading on a uniform shaft of 20 mm diameter solid circular cross section is...

The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...
75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter...

75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter shafts are coupled together using the perfectly meshed gears shown. Shaft DC is fixed to the wall at D and supported with a frictionless journal bearing. Shaft EF is supported with two frictionless journal bearings. The modulus of rigidity of steel is 80 GPa. Before the torque is applied, the angle of twist in each shaft is zero, and the angle of rotation of...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...

Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...

6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP...

6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP at 1250 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 Inche length. The inside diameter of the shaft is 0.8 that of the outside diameter of the shaft. Determine: a) the required inside and...