Water steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s; A1=0.2m2. The exit parameters are: P2=11bars; T2=210C. The mass flow rate is m=2 kg/s. Determine: Exit velocity V2=?; Inlet and outlet diameters D1 and D2
A steam turbine operates with P1 = 5 MPa and T1 = 600 °C at the
inlet, an exit pressure of P2 = 100 kPa, a mass flow rate of ?̇ =
100 kg/s, and an isentropic efficiency of η = 85%. Complete a
thermodynamic analysis of the turbine, using the appropriate data
for water, by finding: (A) The temperature at the exit, T2, (B) the
work produced by the turbine, ?̇ ?, and (C) the rate of entropy
production...
A compressor is takes in air at an inlet pressure of P1 = 80 kPa and an inlet temperature of T1 = 20oC and exhausts it at an outlet pressure of P2 =800 kPa and an outlet temperature of T1 = 200oC. Air flows through the compressor at a mass flow rate of m = 1 kg/s. Assume that the compressor is adiabatic. Find the power required to run the compressor. (Your answer will be in kW.)
A steam turbine, as shown in Figure Q3, operates at steady state with inlet conditions of Pi= 2 MPa, T1 = 480°C and producing 4000 kW. Saturated steam leaves the turbine at a pressure of 0.1 bar where it is condensed at 45.81 °C in the condenser. There is no significant heat transfer between the turbine and the condenser and their surroundings, and kinetic and potential energy changes between inlet and exit are negligible.
A steam turbine, as shown in...
S zet dit e2t - 9et + 14 Oakinlet-71+ in let-2/+C Ob inlet - 71- Inlet-2/+C Oc. šint-71-Ź In It-2/+C Od. et in let-71. get in let-21+
Compiling C Programs into MIPS Assembly and Machine Code sll $t1, $a1, 2 add $t1, $a0. $t1 lw $t0, 0($t1) lw $t2, 4($t1) sw $t2, 0($t1) sw $t0, 4($t1) 1. From the assembly code, what machine code might a MIPS assembler produce? 2. What does this program do? Write the C code for this assembly program.
A gas turbine receives air at temperature T1 = 827 °C and specific volume v, -0.1 m®/kg. Air exits the turbine at P2 = 3 bar and T2 = 450 °C. The volumetric flow rate of air at the inlet is 0.5 m/s. The power output on the shaft is 1900 kW. Determine: The pressure of air at the inlet (pa) in kPa [2 marks] b) The mass flow rate in kg/s [1 mark] c) Find the rate of heat...
A steam turbine inlet is at 1500kPa, and 500°C, and outlet is at 300kPa, and 280°C. What is the isentropic efficiency?
The high-pressure turbine in a steam power plant has an inlet state of 3 MPa, 500°C. A 20% of the inlet mass flow is extracted from the turbine at a location where the pressure is 1 MPa and the temperature is 350°C. The remaining flow continuous to expand in the turbine, exiting the turbine at 2 bar, 200°C. Determine the: (a) inlet and exit flow exergies per mass flow rate of the inlet flow, (b) isentropic efficiency of the turbine,...
A medium-size centrifugal air compressor has 32 radial blades and the inlet vanes allow air suction with no pre. whirl. The rotor speed is 7800 rpm and the tip radius is r2 = 0.25 m. Air is sucked in at a static temperature T1 = 305 K with an absolute velocity V1 = 80 m/s and a mass flow rate of 1.65 kg/s. The total-to total efficiency of the compressor is 80% and the power input factor is w =...