Can i get help on this question. Solve accordingly and upload your LTSpice simulation. Detail solving please.
Certainly the three questions are related and you will solve question 2ii and 2iii using question 2i. Thanks
Can i get help on this question. Solve accordingly and upload your LTSpice simulation. Detail solving...
Please i need help. Can someone solve this using LTspice simulation for circuit design and solve accordingly. Thanks Use a snubbing circuit in parallel with the a diode, also R= 100 ohms and C=100uf for solving. Please upload your LTspice circuit construction 5-18 Calculate the voltage distortion at the point of common coupling in the circ uit of Fig. 5-25. Here at 60 Hz, IsL,21 mH, and the dc side of the rectifier is represented by a dc current source...
10. Two loads connected in parallel draw a total of 2.4 kW at 0.8 pflagging from a 120-V rms, 60- Hz line. One load absorbs 1.5 kW at a 0.707 pf lagging. Determine: (a) the pf of the second load, INV 11. Calculate the line currents for the system shown in figure. Calculate also the total power and reactive power consumed by the load. w 12. For the balanced three-phase circuit in Fig.. Calculate the line currents, the phase voltage...
Please Solve this question as soon as possible Please Solve this question as soon as possible (Power) A three-phane lune has an impedance of Z-04 + /250 per phase The line feeds two balanced three-phave loads that are connected in parallel as shown in Fug 01 The first loads absorbing 560 IVA ato power factor lagging The second load shorts 132 KW ty pona factor The lune-to-me voltage at the load end of the line is 3810.5 V (see the...
please solve the following question by showing the steps ... thanks and ill give u thumb up assume the circuit at resonance where Zeq=R, XL=Xc Question 2: Construct the following circuit on the breadboard using the given inductor with the shown values of R and C. Adjust the function generator to generate a sine wave with frequency 0Vp-p a. = 1 kHz and 0.1uF 匕 1kHz 1k b. Using oscilloscope find the magnitude and angle of the current with respect...
Can you solve the 3 questions using the posted figure? The wave form figure is Fig P3-3. The equations for 3-4 are attached too. Thank you For the waveforms in Fig. P3-3, calculate their average value and the rms values of the fundamental and the harmonic frequency components. 3-3 34 In the waveforms of Fig. P3-3 of Problem 3-3, A = 10 and u = 20° (14 = u2-u/2), where applicable. Calculate their total rms values as follows: (a) By...
solve no: 3.14 , 3.16, 3.19 please show each step and solve for beginners 120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
Hello, can i get help solving this question in physics 2 ? uestion3 A 12V battery is applied to the terminals of a resistor of 1KSQ resistance a) Find the current in the circuit. b) Find the power dissipated in the resistor. c) Assume that the resistor is removed from the circuit, and two in-series capacitors are put in its CL place, where one capacitor has a capacitance of 25nF and the other has a capacitance of 35nF Find the...
please help Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
can someone please help me with this question. I've tried to solve it but I seem to get nowhere. A chopper is used in the regenerative braking of a dc series motor similar to the arrangement shown in Figure Q2. The armature resistance R = 0.02 and the field resistance Rp=0.032. The armature current is maintained at a constant value of la = 200 A The back emf constant Ko = 15.25 mV/A rad s. The dc supply voltage Vs...
Help me solve these questions, please show work. Search 4:52 PM Wed Feb 12 78% A few sample problems from previous midterm 1 tests.pdf 1 of 4 Problem 1: (50 Points) In the following circuit, find V, by either Nodal Analysis Method or Loop Analysis Method. Clearly mark and/or identify, as needed, the nodes, the loops, the variables you assign, the constraint equations (if any), the super nodes and/or super meshes (if any), and the nodes for the KCL and...