Problem 9.8 from the textbook using any method learned in class. - Calculate the voltage Vin...
2. Solve Problem 9.2 from the textbook using voltage divider, and confirm your answer by solving the problem again using mesh analysis 9.2. Calculate the voltage, V, in Figure P9.2. 15 n ww 15 n 15n + V 75 30 V FIGURE P9.2
Solve using Matlab Will leave a like Problem 4: The equations describing the circuit shown in Figure P38 are -1RiRi4 = 0 -Rii4+ Rziz + Rsis 0 -Rsis +Raia + v2 = 0 i=12+i 100 V. (Note The given values of the resistances and the voltage v, are R,-5. R, - 100, R that 1 kn 1000 n) Suppose that each resistance is rated to carry a current of no more than 1 mA (= 0.001 A). Determine the allowable...
(1 point) Note: In this problem, use the method from class. See the lecture notes for January 12 on Brightspace. Also see Example 8.54 in the textbook. More examples (using real matrices) are in Section 8.6 of the textbook. Consider the sequence defined recursively by n+2 We can use matrix diagonalization to find an explicit formula for F (a) Find a matrix A that satisfies n+1 n+2 (b) Find the appropriate exponent k such that Fh Fi (c) Find a...
(1 point) Note: In this problem, use the method from class. See the lecture notes for January 12 on Brightspace. Also see Example 8.54 in the textbook. More examples (using real matrices) are in Section 8.6 of the textbook. Consider the sequence defined recursively by We can use matrix diagonalization to find an explicit formula for F (a) Find a matrix A that satisfies m+1 n+2 (b) Find the appropriate exponent k such that Fi -PDP- (c) Find a diagonal...
SOLVE ALL THE 3 questions using the properties of OPERATIONAL AMPLIFIER AND BJTs. Problem 1 10 Marks A humidity sensor produces linear output voltage in the range of 0 V to 10 mV for humidity levels of 0 % to 100 % respectively. You are required to design the inverting op-amp circuit to achieve the voltage gain of 1000. Op-amp feed-back current should be 0.2 mA when op-amp output is at maximum. Solution: Problem 2 We discussed the summing circuit...
Consider the problem of estimating π using a unit square centered at (1/2, 1/2) and an inscribed circle inside the square. We will estimate π by simulating n darts. For the nth dart, if the dart is inside the circle, then we return In = 1; otherwise, we return In = 0. 1. Are I1, I2, · · · , In independent? Under what assumption? 2. Are I1, I2, · · · , In identically distributed? 3. Let p represent...
<Hw 05 01 Chapter 5 10 of 11 Problem 5.48 Review I Constant Part A The op amp in the noninverting amplifier circuit in (Figure 1) has an input resistance of 400 kn, an output resistance of kn, and an open-loop gain of 20.000 Assume that the op amp is operating in its linear region Calculate the voltage gain (v/v). Express your answer using five significant figures. VAXDvec ? > Figure 1 of 1 Submit Becuest Answer Part 6 NON...
Problem 3: Design Problem On Figure P3a, you have a Common Source (CS) n-channel MOSFET amplifier. Notice the absence of a source resistor Rsig and load resistor R. If we know how the present amplifier (the one on Figure P3a) behaves without Rsig and RL, we can infer its behaviors if Rsig and R were to be added. design the amplifier circuit on Figure P3a, i.e., you have to find appropriate values for RGj You are to RG,, RD, and...
Learning Goal: To use the node-voltage method to solve circuits with branches containing only a voltage source. The node-voltage method is a general technique for solving circuits. Fundamentally, it involves writing KCL equations at essential nodes. When the circuit contains a dependent source, you must write a constraint equation for each dependent source, in addition to the KCL equations. When the circuit contains one or more voltage sources that are the only components in branches connecting two essential nodes, the...
In Problem Set 7 you designed and implemented a Message class. This time, let's design and implement a Mailbox class in a file named Mailbox java. Do the following with this class • You may use the Message class from PS 7. You will have to add new features to the Message class from PS 7 as you work through this problem. You are welcome to start with my sample solution if you wish • Suppose there are multiple mail...