SOLVE ALL THE 3 questions using the properties of OPERATIONAL AMPLIFIER AND BJTs.
Problem 1 and 2 have been solved with proper explanation and diagram.
SOLVE ALL THE 3 questions using the properties of OPERATIONAL AMPLIFIER AND BJTs. Problem 1 10...
thanks Laboratory 1: operation amplifier characteristics A. Objectives: 1. To study the basic characteristics of an operational amplifier 2. To study the bias circuit of an operational amplifier B. Apparatus: 1. DC Power supply 2. Experimental board and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Multimeter...
sedra smith book 7th edition chapter name is operational amplifier. question 12.1 to 12.10 I need all solution with good hand writing. Problems 1075 Transistor Q3 WIL (um/um) 36/0.3 36/0.3 6/0.3 6/0.3 30/0.3 W/0.3 45/0.3 6/0.3 and A, if all devices are 0.3 m long, Q and Q2 are operated at overdrive voltages of 0.15-V magnitude, and Q is operated at Voy 0.2 V. Also, determine the op-amp output resistance 100 k2, C0.1 pF, G = 2 mA/V, R, =...
a. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have one op amp available for this circuit, and a range of resistors with values from 1 kΩ to 100 ka. Draw the schematic of your op amp circuit, labeling resistor values. Make sure the gain, input resistance, and output resistance of your circuit matches the model in the schematic. R=012 *100v, RL 100 b. (5 pts) Your amplifier circuit should have a frequency...
1. We wish to sample a small signal that is on top of a large DC offset using a DAQ (Digital Acquisition System such as your nscope) that has a limited input voltage range of ±5 V. If the signal is modeled as Vin-0.1sin(ot)+10 V where 0.1sin(ot) V is the signal and 10V is the DC offset, design a circuit using two op-amps that first removes the DC offset then amplifies the signal by a factor of 40. 2. Repeat...
Please show all work, step-by-step solution. I don't understand how to this problem. stor is equal to loke (R = loke) Below is an Op-Amp beised amplifier. Each resistor is equal to loke 1) Assume that the Op Amp was ideal except it suffers from the offset Voltage Voh, Find the resulting DC enor wItage that appears in the output Voltage Vo. Assume that the Op-Amy nas ideal ercept that it's saturation voltage is lov, Saturation current is : 25...
Problem 1: Given the OP AMP circuit shown, answer the following questions. (a.) Write an expression for the output voltage, vol(l) if (b.) The source is now a time-varying voltage source, the input Vim) 12 V DC Vim(t), and R 2.5k2, R2 5k2 and C-20nF Determine the output voltage, voll) using Laplace transforms R2 (c.) Draw the straight-line approximation (Bode plots) of the gain and phase responses in ot) o Voct)
need help for d,e,f OP-Amp Circuit R-20k Fig 1 1. Design an operational amplifier circuit using an LM741 op-amp and a 10k the diagram shown in Fig 1 to produce the output voltage feedback resistor that represents Clearly write your ID number in Table 1 Table 1 Your ID Number 3775。73 . Set up the roquired gain numbers as follows and write them in Table 2 Ai- the last digit of your ID number+5 A2-the 2ed last digit of your...
#1,8,9&10 please i need 1,8,9&10 Show your work for full credit. 10 points per problem. 1. What is the output voltage of an ideal op-amp with an open-loop gain of 500, if the input voltages are: vi(t)-0.5 cos(2000t) + 20 cos(120axt) v2(t)-0.5 cos(2000xt) +20 cos(120axt) Using the Lab 11 configuration below, if we increase the temperature of the thermistor by 15°C: 8. What is the output voltage of the Wheatstone Bridge? 9. What is the output voltage of the Unity...
Problem #1 A large warehouse has five temperature sensors located in five different places. Each sensor circuit is indicated as the figure below, where a DC current source circulates through a temperature-variable- resistance. Tk is the temperature in Celsius at the sensor in a given location; Tref is the reference temperature that each sensor has been calibrated. Assume for this problem that Tref 27 °C. Therefore, each sensor will provide a positive-voltage for temperatures greater than the reference, on the...
<Hw 05 01 Chapter 5 10 of 11 Problem 5.48 Review I Constant Part A The op amp in the noninverting amplifier circuit in (Figure 1) has an input resistance of 400 kn, an output resistance of kn, and an open-loop gain of 20.000 Assume that the op amp is operating in its linear region Calculate the voltage gain (v/v). Express your answer using five significant figures. VAXDvec ? > Figure 1 of 1 Submit Becuest Answer Part 6 NON...